Canpump Pressure Washer Axial Pump, 2500 psi at 2.2 gpm, 7/8-inch Vertical Shaft

1. I was sent the wrong installation Instructions in the box. They sent instruction for 3WA-3025A which is a horizontal mount pump. 2. The install required the use of some spacers between the pump mounting bracket and the engine/frame mounting holes. Without the spacers the hex bolts at the top of the pump interfered with a secure and level installation and caused the shaft to bind. I always test the shaft to make sure it turns freely prior to starting the engine. Now, I have an older model 5.5 HP GCV160 Honda engine and maybe this is not an issue with newer models. 4. In my experience vertical shaft pumps don't usually have a breather tube. This one does and when I initially started the engine after the pump was installed it threw a little pump oil from the breather tube. It seemed to stop after it ran for a while so hopefully this will resolve itself as excess oil is blown out of the breather tube. I did not add any oil to the pump as I could tell it had adequate (maybe too much) oil as shipped. 5. It had tremendous amount of pressure for such a small pump so hopefully it will last. I ran it with the pressure control knob turned up all the way. I may dial it back a turn or two. Seller can greatly improve service by sending the correct paperwork for the pump and maybe giving more explicit information on the oil level and the breather tube. If this pump craps out quickly like other reviewers have said happened to them I will come back and update. So far I am happy after a bit of frustration getting it installed.

I used this product for my troybuilt model 202292=1. The pump did fit. But the big problem is the water inlet is facing the wrong way. It faces to the front insted of to back. This causes a problem when trying to move forward with water hose in front. Another problem the engine labors when I start to spray. when i checked the specs.my 5.0 HP engine should have been adequate. On installation had to buy quarter inch spacers and longer bolts.Other than that the two big problems is the water inlet facing forward and the engine laboring. Is it possible to reverse the water inlet?

Installed easily but had to use some spacers to mount the pump correctly. The pump did come with a breather valve and a tag with instructions to remove a plug from the pump and install the valve. The threads snapped off and I had to reinstall the plug and discard the breather. I did contact the manufacturer and they were willing to send another one but also stated that it was not needed. After installation the pump worked great.

Inlets and outlets were different from what I replaced, not quite as convenient but still works fine. No directions included, and washers/spacers are required. I did expect that this was a possibility from one of the photos in the product ad. I expect that with the brass housing that it will be subject to less corrosion than the pump that I replaced.

well constructed but you will need to adapt this pump with spacers for most jobs

This pump is warranted for one year. It automaticly shuts down when overheated.

110% completely satisfied!!!!

Live my pum

Used this to resuscitate a Wal-Mart brand Power-It pressure washer.. which i believe is built with a very nice Honda clone engine, but tragically was equipped with a really cheap pressure pump unit, it split in half in its second season. You get what you pay for!So... transplant pump needed - found this one and it looks good - This new Canpump pump is a million times better quality and constructed with ample amounts of brass! Everything lined up, only needed some spacers and slightly longer bolts to have it bolt up to the underside of the motor and pressure washer chassis since the crank shaft came out quite far. Spent the weekend washing stuff - Very Happy. When it comes to winterizing, I am going to remove this beauty from the motor and put it under my pillow.

Bought a pressure wash from walmart. Pump blew apart after 2 years. Replaced with this pump, seems to be much higher quality. Works as it should. Inlet and outlet are located differently then the original but works perfectly fine. Install was super easy and only took about 10 min. Did require some washers to space the pump off the motor a bit. Very happy!!!!!UPDATE!!Bought less then a year ago. Used twice last year. Put away for the winter (in the basement, away from the cold) pulled it out to use it the other day, worked for about 5 mins then the pump split right in half! Not a long lasting product buyer beware!!!!!!!!

Perfect! I am not mechanicaly inclined and was able to do this repair in a relatively short time. I did have to go get a few washers. The legs on the original pump were 1 1/4”, and on this one there are flush. No big deal I was able to use the original bolts and nuts. The local repair shop wanted $300. And a week or so! (To Change the pump) This cost me $123. Including taxes and free shipping, plus it was on my door step in 2days! Also, the new pump is a better design. The intake and outflow are at the pump, not both out the back with a 10” extension like on the original. Making it very difficult to drag the pump to where you need it without the extensions digging into the ground and getting full of dirt and crap. On this one the intake is in the front, i added a short extension for ease of use. Mine is a Briggs and Stratton model # 020440 pump model 201112.

Worked great at first stored it for the winter. Winterized it like I always have done. Oh let's not forget that I am a 40 year service technician. Stored indoors took it out in the spring hooked up the water purged out all air before starting. Started first shot pump failed had no pressure. So I figured it was a disposable one time use pump. Not at all happy would not recommend this but have yet to get feedback from manufacturer. Will update for sure.

Pump worked good so far put about 2 hours on it still working I would have given 5 stars but the outlet is odd size or is 15mm inside instead of the common 14mm . The adapter is hard to find and more then I wanted to spend . I did end up making one cause I could so just be aware of that fact.