GODO USB 3.0 to 3.5 Inch Hard Drive Enclosure, Vertical External Hard Drive Docking with Stand for 3.5 inch SATA HDD SSD, Aluminum Alloy Drive Case Support Up to 18TB with UASP,Power Adapter

This is an excellent enclosure. I have purchased many different brands of HDD enclosures over the last 30 years and this is one of the very best. It is sturdy (aluminum, not plastic), easy to mount the drive in, and attractive. They even enclose a screw driver along with the screws needed to attach the drive. It worked perfectly with my old 1TB Seagate HDD and I am getting the expected transfer speed. It comes with a power supply (cable) and a USB 3.0 cable to connect to your computer. Highly recommend.

This is an affordable quality product that works great for housing a 3.5" spinning hard drive. I wouldn't recommend it for 2.5" form factor drives (spinning or SSD) since there is no way to secure a drive that size inside the case.

Enclosure is well made. It is easy to install hard disk drives ( up to 2 ). Disk drive(s) work best when connected to a high speed USB port. Enclosure can get a bit warm.

Godo USB 3.0 External HDD Enclosure arrived in secure, well-cushioned packaging. Constructed from aluminum alloy, it offers improved heat dissipation but also provides a sleek, minimalistic design that's easy to handle—even for first-time users. Installation: 1) Attach the two plastic side rails to your 3.5" SATA HDD. 2) Remove the rear panel of the enclosure, slide the drive in carefully, aligning the SATA interface with the enclosure’s PCB. 3) Pull the drive forward until the connectors are snugly seated, then reattach the front panel. 4) Secure both ends with the included screws for a firm, rattle-free fit. The enclosure includes both a 12V power adapter and a USB 3.0 Type-A to Type-B high-speed data cable, ensuring stable power delivery and fast transfer under optimal conditions. To access your files: Connect the USB cable and power on the enclosure. Your system should detect the full drive capacity immediately. If you're seeing only partial capacity (common with drives over 2TB): a) Log in as an Administrator. b) Open Disk Management. c) Right-click the drive's label (left-side column), and select "Convert to GPT" (GUID Partition Table). d) Once converted, the full capacity will be recognized and accessible. Overall this enclosure is a cost-effective, efficient way to repurpose high-capacity SATA drives (2TB and above). Whether you're backing up data, transferring large files, or bringing an old drive back to life,this USB 3.0 enclosure delivers reliable performance and exceptional value.

data transfer is really fast which is actually surprising with the ridiculous lag win11 introduced. Metal frame allows heat to dissipate better than the plastic ones which is nice with very large data transfers. This drive enclosure works just fine with a 24TB data center drive despite them saying it only works to 20TB, though I did have to resolve the 3v issue on the drive with a piece of tape (leave yourself a note in the enclosure lol)

This enclosure is excellent. Easy to assemble and very good quality aluminum. The hard drive fits snugly and is held in place. I had previously purchased a similar case but the hard drive was not held securely in place inside the enclosure and even worse it was shipped with a European style plug, so it was useless in North America. This one came with a standard US plug. I also like that it has an On-Off switch and a blue LED to let you know it is running and it can stand vertical or lay flat. I'm glad I found this brand.

I had this item sent overseas, so when it arrived defective, instead of returning it I decided to "fix" it. The fan inside was not spinning. Apparently the fan header that supplies 12v was dead, so I hot wired it to the 12v voltage switch. The enclosure was still hot to the touch, so I used some power tools and cut holes in the front and back of the unit so the fan can push better air flow. There is a black plastic sticker film inside that separates the drives area from the electronics, and the fan. So what point is that to have a fan but the air can't flow past the hard drives. I removed that too. So now, the fan spins fine, there is adequate ventilation to push through the hard drives. It's still a little hot but not so bad. The functionality isn't the best. You can't format a drive IN the enclosure and then remove it and expect it to work solo in the PC, because it uses virtual block sizes or something with the crappy Jmicron chipset. There are ways to get THAT to work but it's very complicated. The other thing I didn't like was it's constantly powering down (and up) every 10 minutes or so, with no way to turn it off. The firmware is stuck on power saving mode after 10 mins. Does not matter USB power saving settings. I got around it by creating a cron job in linux (which it was connected to) to touch a file every 5 minutes. If you like it powering down every 10 minutes more power to you, but I find that something will poll the USB bus, or poll the attached hard drives, especially in Windows and constantly spin up down up down up down the drives in the enclosure and that creates a lot of wear on the drives, so be sure they have a good warranty and you're using RAID 1. I'm a little harsh on my 1 star review but to be fair I DID have to open it, mod the fan to make it work, mod the case to make it vent air, and use tricks in the OS to keep it from powering down. It's not worth any more than $30, and that's mostly for the cost of the aluminum LOL.

This enclosure (the one pictured) works very well. I use it for an external 1TB disk for daily backups and it's always connected. I like the activity LED which lets me know when scheduled backups are active. One thing I noticed, however. I have it plugged into a USB3 hub with individual switches to enable/disable the ports. The switches work to disable OS access on every device I've tried EXCEPT this one. The device is recognized and is useful to the OS whether or not the port is enabled. I assume it has something to do with the fact that the enclosure is separately powered. Something to keep in mind.

Speed of transfer excellent

رائع مثل الوصف ، مستخدم الماك يحتاج USB-C to USB-A Adapter

Intended to use as a permanently connected enclosure for backups, but included USB cable is way too short and does not reach my PC which is hanging from under the desk. Will keep it and still use as a monthly backup tool, but will need to connect and disconnect to the front of the PC each time. Be aware of this important limitation.

Cet appareil surchauffe. Le ventilateur, si il y en a un est complètement non performant! J’ai retourné 2 appareils de suite.

I had trouble to create RAID1 setup on Linux and Windows 10.