PC Products PC-11 Epoxy Adhesive Paste Kit with Mixing Tool, Two-Part Marine Grade, 1/2lb in Two Cans, Off White, (20128)

Some of the best epoxy that I have ever used. Just make sure that you don't use too much hardener. Use equal amounts, but if you are a little heavy on the glue it will still cure, but not if you go heavy on the hardener.

Simple to use and doesn’t setup too fast. Gives plenty of workability.

Mixing it is a bit of a pain but application is great, the mixed product is thick enough and stays in place during the entire drying time and becomes extremely solid.However it seems to be too solid that even with 60grit sandpaper it's a bit hard to give it the desired shaping.After letting it dry for 30 minutes, it's more like play-doh and can be adjusted slightlyI would recommend putting on gloves and shaping before letting it fully dry and will be doing this on the next project

I initially purchased this epoxy kit based on all the positive reviews to fill accessory holes on the interior gel coat ceiling of my shuttle bus conversion. This stuff is easy to mix, easy to apply, and (most importantly) it just works. I then decided to use this, instead of Bondo products (I HATE Bondo) to repair body damage in the fiberglass body. As expected, it filled quickly and easily and cured to a rock hard repair. After sanding and paint, the repaired areas are indistinguishable from the rest of the body. After 35+ years of using all the other brands of epoxies, I tossed all the others from my box and this is my sole fiberglass epoxy from now on. Buy it, you will like it,

This epoxy REALLY holds. I've repaired wobbly kitchen drawers, a plastic shelf inside my fridge, glued 2 garden rakes back into their handles... just don't get it on anything you don't want messed up. It doesn't wipe off easily and it's thick and hard to manage. It dries bleach-white and hard as cement. Mixing equal parts of it isn't the most fun, cause it doesn't easily clean off your 'measuring spoon'. You obviously don't want to get any of 'Part A' into 'Part B', so it's best if you have two same-size measuring utensils. Definitely WEAR SURGICAL GLOVES when you handle this stuff. It's not like the 2-part Devcon stuff in the squeeze bottles, which doesn't always hold to certain plastics. I haven't found anything so far that this WON'T mend. It doesn't dry flexible - it will spike you if you don't smooth it before it dries.

Worked fine, I mixed by weight, no slump, stiff, easy to use strong waterproof, I expect the repair to last a long time . I'll buy this again.

I have to remember to reorder more of PC-11. In 10 weeks, I've almost used it all up. I have repaired a variety of things with it.... plastic pump discharge port, plumbing, electrical. Great product.

I was told about this two part epoxy by a sculptor friend of mine, and since then I've been using it for nearly everything around the house. This was the second time I've purchased it from Amazon, but you can also find it in hardware stores. It's a paste so it does a fantastic job of reparing things with missing pieces. I recently dropped a marble soap dish and couldn't rescue all the shards. This allowed me to repair it and I painted the crack where it broke so now it's a super-fancy-marble soap dish with a 'metallic' crack.If you're reading reviews on epoxies you likely want to know how well it holds. It holds extremely well. I can verify that it's a permanent bond if you mix the ratios correctly. I have a Toyota and the "T" on the front of the vehicle popped off (it's held in place with plastic notches and one of them broke). I used this to stick it back on and it's lasted for two winters and plenty of days over 100 degrees in the summer. It's sandable when it dries and accepts paint readily. I have nothing but good things to say about this product, it works like magic!

I used it to repair some old gnomes that had cracks and missing pieces like the nose etc. It worked really well in filling in the holes and moulding them a new nose and I was able to paint over it no problem. I was worried about messing up the mixing process but it turned out good it wasn't a problem.

I used this for fixing my reel seat on to my fishing rod, I like that it is a paste and does not drip.

Still got the original leak, not as waterproof as claimed

All good. The end product colour is a blueish white. I wish it was pure white.

Did what I wanted it to.