CREWORKS 10L Ultrasound Cleaning Machine with Heater and Timer, 240W Stainless Steel Ultrasonic Washing Machine, 2.6 gal Professional Ultrasound Parts Cleaning Machine for Lab Tool Glasses Auto Part

The delivery person was nice enough to put package in my lean 2 since it was raining. As for the product it does alot better then I expected put some rusted brake parts from a atv in there with some evaparust 30min vibration and about 90min of 175deg heat parts came out look great saved us alot of time since was able to do it during lunch. We have also just to test it put a old atv carburetor covered in grease and dirt with just water and soap set for 20m at 175deg took 90% of the crap off. Yes you do have to let it warm up for atleast 10min first

I've been looking for quite some time, trying to get myself to pull the trigger on an ultrasonic cleaner. I finally did it. I periodically work on outboard motors and other small mechanical items. I though long and hard about the 6 liter size, but finally decided I needed to go big, or not at all, so I purchased this 10 liter cleaner. In combination with some powdered cleaner solution, this cleaner does real well. It take a little while to heat up, but otherwise works as advertised. The problem I'm having right now is that I don't have anything really dirty to test it out on!I chose the fully mechanical model in order to avoid potential problems with circuit boards, etc. I opted for manually set rheostats instead of LED panel.

Works as it should. Gets plenty hot. A bit noisy though.

I bought this primarily to clean air guns used for painting and drywall texturing. For paint guns, I have found that it takes a few cycles to really get them clean.The tank does get plenty hot, and overall build quality seems good. Noise level is acceptable and not more than expected for this type of machine.My primary complaint is that paint that was cleaned off the air gun components by the machine sank to the bottom of the tank and apparently baked onto the stainless steel. The pattern it baked into is a rectangle, which I’m guessing is where the heating element is under the tank.I have not been able to remove it using either physical scrubbing (which I did lightly so as to not scratch the metal) or chemicals. It doesn’t appear to affect the ability of the machine to clean, but it is annoying for the stuff you’re cleaning off parts to bake itself onto the center of the tank.

As I was packing it up to get a replacement, I noticed it had a fan on the bottom of the machine. THE FAN NEVER WORKED AT ALL! Without the cooling fan, it was heating up all the electronics inside and possibly might have started a FIRE! A foul toxic smell was coming out of it. And I mean TOXIC, like burning plastic.I ran it for 15 minutes to de-gas some cleaner. If used on the floor its hard to read the knob settings. After 15 minutes the heater smelled like burning plastic, like its just about to burn itself out. I had to close the door and run a room vent fan because it stinks. I'm wishing I had got one with digital readouts, easy to read. Its very noisy but they just do that. The transducers are very strong, so thats a positive. They are sending me a replacement on sunday, THIS is why I usually buy these kinds of things on Amazon, so I don't get stuck with trying to get a refund or hopefully a replacement that works like its supposed. This model sure does get some bad reviews for not lasting very long. I would recommend spending a bit more money for another brand with better reviews and better made.

I just got it, so I reserve the right to change this review if it doesn't perform, but based on INITIAL observations, this unit is heads and shoulders above the three Vevor cleaners I had before. I went with the manual dails instead of the digital due to the fact that I always had issues with the digital machines. Time will tell if this one lasts longer. The only downside I see is that the lighted power switch is on the back. Once the unit reaches desired temp, there are no lights on the front. So leaving the shop for the day, you can't tell by looking at it if you've left it on or not. You have to pull the unit out and look at the lighted switch on the back. An indicator on the front letting you know if it was on or off would be best.

Very useful and inexpensive quality ultrasonic! Heating element works fast!

Works great, seems well built. Pretty loud, but adding a bit of electrical tape underneath the lid helps. The only issue is, the heater is not linked to the timer. So, set timer, walk away, come back to boiling parts. And "175 degrees F" is nowhere near accurate, since it was literally boiling my Simple Green. But I'm ok with something over-performing.