eSUNABS+ Filament 1.75mm, 3D Printer Filament ABS Plus, Dimensional Accuracy +/- 0.05mm, 1KG Spool (2.2 LBS) 3D Printing Filament for 3D Printers, Black

PrusaSlicer has a profile for this but the temperatures are off, bad layer adhesion until I ran Orcaslicer's temperature tower for ABS and found out it's WAY BETTER at 245/100 now it prints beautifully.

I am not new to 3d printing. I have purchased well over 200kg of filament from Amazon (I counted), and many more from other sources like Micro Center, and even direct purchases from manufacturers. Esun ABS+ is the first filament I have had do actual damage to my printer.I was printing with this roll of ABS+ on one of my Creality K1s. I had previously printed a few parts for my voron build, but the filament spool was mostly full when I put it on the printer. When it had been stored, and when I put it in the filament dryer, it was clipped to the spool so it wouldn't go slack. I don't use modified spool holders with ball bearings... I mention this because a few disbelievers think I let the spool go slack and induced the tangle myself... I did not.The prints were going well until the spool was down to about 15% full, and then it encountered a massive tangle.... you can see it in the pictures I uploaded. after taking the picture, I disassembled the snarl, and the over-wrap was 8 strands deep.Anyway, as the printer has been reliable for over 15kg of filament, and since the prints I had run prior to the failed one were all good, I left the printer unattended for a several hour print. Unfortunately, this was the time when the evil unicorn roll of filament attacked.Spool tangles are not common from factories... but they do happen. If a roll slips off the spooling machine while winding, or if the line pauses during a run... or some other failure allows the spool to go slack enough... an overwrap can happen. Tangles are much more likely to be caused by user error... but in this case, it was quite obvious that I hadn't induced this failure.Obviously, I lost the print... not a big deal as prints fail sometimes... but it was worse than that. The K1 extruder has a really positive grab on the filament... and it uses one of the little nema 14 steppers. Rather than grinding the ABS into dust and breaking the filament, it jammed and overheated the motor... it also kinked the ptfe tube and crushed the fittings on the filament runout sensor and extruder. I have never seen so much damage caused by a roll of filament... sure, filament can clog up an expensive nozzle, or jam in other ways... but this cost me over $50 to repair... (new extruder assembly, and a replacement fitting for the filament sensor.)I contacted eSun customer support... and after giving them all the photos and information, they offered to refund 20% of the cost of the roll of filament... They did offer to go up to 40% of the roll (about $7) but that was their final offer.I wasn't trying to get a new printer out of them or something... I didn't figure they would even pay for the repair parts... but taking responsibility for the defective roll, offering an apology and a replacement (not just a discount on a new roll)Needless to say, I won't be purchasing another roll from eSun. Other brands of filament have replaced bad rolls free if they were delivered wet or fragile... Customer service is everything... eSun's customer service is not.

I'm reviewing the black eSun ABS+ filament. This is now my most purchased filament. I haven't had any print failures (other than a belt failure which is the fault of my machine). If I print at 240-245, it has a beautiful matte filament. Friends ask specifically for me to print things for them in this filament because of the look and feel. I print a little warmer for layer adhesion, which is fantastic. It's one of the cheapest filaments I purchase, and it's the best all-around material and usually my first choice for a functional part. I have filaments that are stronger, but not as tough or temp resistant. I have tougher filaments, but they aren't as stiff. All of my "performance" filaments cost more than this filament.With ABS, companies can vary the amount of A, B, and S in the material, so everyone's is a bit different. This is a great composition. It does have the styrene smell (the "S" in the name) like ASA and HIPS do, so I don't print when I'm in the same room until I can get my vent system working. If there are "low odor" ASA/ABS varieties, they'd probably have less styrene, and this material has a perfect amount so I'll take this tradeoff.I'm still kind of amazed that this material is such a great all-around material and pretty much the second cheapest filament I buy. I've paid much more money for inferior filaments that were harder to print.I print with a direct extruder onto a smooth PEI spring steel sheet, sometimes covered in magigoo, sometimes without. I print in an actively heated chamber at 45C. I'm not sure how this prints in a passive enclosure or open printer.

Good value, nice colors, no clogs or tangles. Works great with my prints,

Prints fairly well, but I have been fighting some warping issues, even more than some other regular ABS I have. I would have assumed ABS+ would be easier, but so far it has not been.

I've been printing for about 6 years on several printers, at 240C (recommended temp) in a heated chamber, this has some of the poorest layer adhesion I've seen from ABS. A hollow cylinder with 4 perimeter walls basically shattered with only light use. Would not recommend at all for functional parts.

The media could not be loaded. As you can see in the videos, had one perfect print, and then a ton like the others. From stringing and small imperfections to poor adhesion fails. I do 245 C nozzle and 95 bed temp. tried both .2mm nozzle and .4mm nozzle. Thought I'd experiment and try and save a couple of bucks while trying some different colors but would not recommend.

ABS good for strong prints! The smell was not that bad than other ABS but maybe it was my ventilation I don’t know but good for price!

eSun filament bevalt mij samen met Polymaker het beste alleen is eSun even voordeliger. En je gebruikt er ongemerkt toch een hoop van.

Bonjour très bonne bobine abs facile à utiliser et a réglé très bon rendue je recommande vivement

Once temps were correct, it was easy to print with. No need for glue or anything if your build plate clean enough.

Tienes que contar que para imprimir abs hace falta enclosure y si es calefactado mejor, en mi caso no era calefactado.En cuanto a la resistencia de las piezas impresas muy bien todo la verdad es que me sorprendio.El producto calidad precio esta realmente bien. yo he trabajado con muchas marcas y este caso me quedo con sunlu como principal filamento

Mała kurczliwość