INSULATION MARKETPLACESmartSHIELD -3mm 24inx10Ft ReflectiveINSULATION Roll, Foam Core Radiant Barrier, ThermalINSULATION Shield - Engineered Foil

This stuff is truly amazing. Made a windshield screen out of it, and it is crazy how much heat pours in when we take it out of the windshield. We used foam board to insulate our campervan, but if I'd known about this stuff, I would have used it instead.

Excellent for RV use ...WindowsIn cabinets on slide outs .Many great RV uses ...save money

Keeps the heat and cold air in my room does exactly what it is supposed to great product works very well.

Just put this up in my window yesterday. The sun hits my window with a vengeance in the morning, as my house faces east. Seems to work really well, I noticed how much cooler my living room is right off the bat. But one thing I can do without is the smell of heated metal. It literally smells like something is going to catch on fire. Hopefully it wears off after awhile or I’m going to have to replace it.

I bought it for my RV to keep cooler inside, and it did its job. It's made of good material and worked perfectly for us. And it is easy to install.

Premeasure your window inside frame to frame. Lenth and width.Then measure and cut the product to size.You will need neavy duty double bac tape to secure it.We will find out tonight how well it works. So far its blocking out sounds that we don't want to hear.

I used this to insulate a small area of my basement for indoor seed starting. Previously that area was very cold, and had effectively no insulation between it and an outdoor crawl space (aside from a few semi-loose plywood boards), and the area was also on top of a big poured concrete pier/slab thing. So basically, the air was around 50 F in the winter and the surfaces were cold. Also, drafts (outside air) came in from the crawlspace through slits between boards. This is despite all the seed starting gear (lights, heating mats, etc.). In previous years I have even put a small space heater down there in an attempt to try to get the soil up to 60 F+, which is where I want it to start things like sunflowers.So I bought a 50-foot roll of this stuff and cut three 14-foot strips of it. I tacked one long strip along the area that meets the crawlspace. (Used a staple gun—not sure if that's the right choice, but it's what I had.) I also laid a long piece on the concrete surface (no attachment, just laid it down and put plant mats directly on top of it), then added a third piece that ran between that surface bit and up to the wall/crawlspace interface. I stapled the that third piece onto a wooden beam, and used packing tape to attach the lower pieces where drafts were trying to blow through. This allowed a mostly leak-free insulation shield about 6 feet "high" by around 14-ish feet wide. I put back the same temperature monitor that had read 50, and within a few minutes it was up to 55. Hmm. That's good.After I reinstalled all the seed starting stuff (a few low-power heating mats, four low-power LED lights), the temperature went up to 65 degrees and stayed stable (!!). I have seen a few dips overnight down to 62, but in general this area that was consistently 50 degrees F (WITH lights and heating pads) is now mostly 65 and up (at one point it reached 70, which is actually pushing it as far as seed starting is concerned). The space heater is gone—it would be way too hot at this point, and in fact I'm considering adding a fan or something, triggered in case the temp gets close to 70, just to circulate some of the heat away.For the price, I'm extremely impressed. This stuff definitely created a thermal barrier between the super-cold cement block that the seedlings sat on—that block is such a huge mass that there's no way a heating pad is going to ever warm it up (remember, we're in a basement and this is essentially a secondary foundation wall that just happens to be super wide). The insulation also created at least a basic vapor barrier on the interface w/crawlspace, blocking a lot of drafts and little gaps. The fact that it's so thin and easy to work meant I could also tack it up around edges and corners, which is where the drafts were the worst. I know this isn't really designed to be the only insulation in this use case (I might have been better off installing batts of fiberglass, and would certainly do so if I were trying to treat an entire basement), but it's cheaper, MUCH smaller, MUCH easier to work with, AND you can wipe it down (within reason—it IS possible to rip the shiny surface). If you're looking for something very thin with a good radiant shielding effect, this is it.The only downside I can think of is that the material is thin. While this is usually a positive, you do need to be careful with it, as it's possible to rip the foil layer and have it start peeling off. That's different from a lot of other kinds of insulation (fiberglass batts, foam board, spray...) where the material itself is real tough and workable. This is thin and precise—install accordingly.

I used this insulation to line the inside of a home-made 3D printer filament dryer. Unfortunately, the insulation seems to have done very little in the way of improve the heat loss through the sides of the dryer. The outside of the box still gets just as hot to the touch as it did before I installed the insulation. I have noticed that it will reach an internal temp of 80 deg C in a little over 24 minutes, where before it would take about 26 to 27 minutes to reach the same temperature. So it might have added some insulation value, just not as much as I would have hoped. but I can see I am still loosing a significant amount of heat conducting through the sides. Because after running for 90 minutes, the exterior is still holding steady at around 58-63 deg, which is the same as it was before the insulation was installed. I havent measured the amp draw of the heating element to see if that shows a reduction in amperage over time. but just a ballpark guess, the heating element seems to turn on and have the same duty cycle as it did before. (didn't time it before installing to get a baseline measurement, just not observing any noticeable obvious improvement).Otherwise the insulation was easy to install. I used a high temp double sided tape to secure it, which seems to hold well, The foil coating appears durable. and over 8 hours of continuous exposure to 80 deg hasn't damaged, discolored or otherwise affected the insulation in any way that I can tell.