Crazepony 4pcs 5.8G FX798T FPV Brass Antenna 35mm Omnidirectional Weld Connector for FX798T FPV Micro AIO Camera

Perhaps I have the wrong product, I was looking for dipole antenna, I heard they got great distance, however these do not, they get about the same as my inductrix antennas. But I wanted to replace my clover leaf antenna, so I changed it and it cut my distance by about 50 feet or so.. Also I found the wire at the bottom was a little too short to splice and solder to the camera.. after separation there was very little left to stick up.. maybe that is why I am getting a short distance, but I see others that are already placed and I see that they are this long but attached? so they are a little short.. But I did get four of them.. and they where not that expensive so I gave a big 3 stars for the fact I did connect 2 of them and they did work.. Just not as good as I was hoping..Update : They did send me another 4 to see if it would help... Which I think is just great that they care enough to just send those out to me, the stems are still a little short for me to solder, but I bet a pro would have no trouble attaching these to their cams.. I have added an extra star for their service.. But I will have to stand with my first assessment of the product for my uses... This is most likely how all of them come, I just may be a bad solder guy.... But they did make good.. thanks.

Great, Easy to replace, far better than "fixing" your CP antenna.Over the last year, I've completely destroyed my 5.8ghz RHCP antenna that was on my vtx. Held together by globs of solder, the quality got worse and worse until I yanked it off to put on of these on it. BOY was there a difference. Perhaps I had just gotten used to the snow-filled screen with my beat up antenna, but the picture with this little dipole was terrific. Paired with a proper foxeer CP antenna on a my goggles and there seems to be pretty good penetration through the office walls. :)One little nit, since I often fold it back to fit in the case, the plastic covering was breaking the outer braided shielding. Once the plastic is stripped, the antenna is a fair bit more flexible and less easy to damage.

Good replacement for the cloverleaf antennas which come on a lot of micro FPV quads. These are rugged enough not to get all bent out of shape if you flip over on landing or have a crash. After soldering one of these on, surround the soldered joint with some hot glue for added protection. Works best with a linear patch antenna, like the Menace RC Bandicoot.

The media could not be loaded.  You need these in your Tiny Whoop Pit Kit to keep your FPV transmission static free. Take the guesswork out of antenna wavelength for the best weight to signal signal value with a pack of these handy 5.8g band antenna leads. They give a great signal and ultra lightweight at only 0.20g each!The video shows how I made a FuriBee F3 FrSky build from thes camera shell and other Craze Pony performance Tiny Whoop Inductrix parts: Crazepony 4pcs Propellers Red and Tiny Whoop Eachine E010 RC Quadcopter Frame Crazepony 4pcs 6x15mm Motor (Speed: Faster) 17500KV TW Special Sauce Edition for Blade Inductrix Tiny Whoop with Micro JST 1.25 Plug Bonus Rubber Rings [[ASIN:B01N3QP04N Crazepony FPV Tiny Whoop Camera 5.8G 40CH 25mW Transmitter with Circular Polarized Clover Leaf Antenna for Blade

Everyone I fly micro quads with seemed to have issues with my 4-lobe cloverleaf RHCP antenna on my VTX even though my video was fine. They all use dipole antennas on their VTX's and I used CP. I tried to use one of these antennas and their problems seemed to instantly vanish! The only thing I changed was soldering on this antenna. I still blame their equipment mismatch (dipole VTX with CP receiver), but now I can fly without drama. My CP antenna works better for maneuvering, range, and overall quality, but this antenna isn't that much worse.

They work ok, however, antenna lengths aren't cut to the correct length. These are ok for zipping around the room but if you're planning on flying outside you'll want to make sure to make adjustment to the length of the exposed antenna.

I thought I was screwed after one of my crashes. I had fixed my antenna lots of times but it got ripped off in a bad crash. I installed [ with some help from youtube] this Crazypony brass antenna and it seems to be better than stock. I don't solder every day and I'm not that good but I found that it was easier than I thought.It gave me confindince at my new found skills. I love this hobby! Thank you. good luck.

Great antenna's! I swapped this for the cloverleaf on my AIO whoop camera and ditched the vtx protection. What a difference in style, durability, and weigh (felt when flying). Doesn't come with any instructions but it is obvious and there is YouTube for everything. Comes Pre-Tinned and was installed in less than 1 minute.Don't think I will be needing more than 1 of the 4 I have but I would definitely buy these again! Highly Recommended for Whoops!

cool