Creality Ender 3 Max Neo Bed Upgrade, PEI Sheet 310 x 320mm Removable Magnetic Flexible Texture Surface Heated Bed Plate Build Surface for CR-10S PRO/CR-10 V2/ CR-10 V3/ CR-X/CR-X Pro/Ender-3 Max

I have an Ender 3 Max Neo. I'll get my one complaint out of the way right now; the rear clips make it very difficult to put the magnet down straight. I probably could have taken them off, but I'm sometimes lazy.Now for the rest; this thing is pretty crazy. You have to heat it up about 10 degrees C higher than your usual glass/metal build plates, but when it's up to temp, prints stick perfectly. And the moment it cools down to ambient, the prints slide right off. In fact, it's so good at that, that when I've forgotten to adjust the temperature in the slicer, my prints have just slid around the plate (the printer is in a cool garage). Incredibly easy to clean, looks great with the understated gold, and worth every penny I think.

After buying my Ender 3 V2, it was printing fine in the beginning. Then I started to get the adhesion issues, which I initially could solve by washing the glass panel in the dishwasher, then dishwasher with alcohol cleaning. In the end nothing was sticking anymore, and elmers glue was the only option left.Since I had good (initial) experiences with the glass platform, I decided to buy a new one. I went through the same struggles, but then I had a PETG print stick to it with a vengeance. So that one became a write off too, since I damaged the glass.After reading a lot of articles online, I decided to give a PEI sheet a try. So I glued that one to the scratched plate, and it worked fine. However, larger prints were sticking too much.... The PEI was by itself very good though, so the obvious next try was this flexible bed.I can only say that I am very happy with this purchase. I can recommend this upgrade to anyone who just bought their printer. Great adhesion, and very smooth. So your prints will be very smooth too!What I do is clean the platform every single time before use with 99.9% IPA, which I have anyway for my resin printer, and I have yet to run into adhesion issues.Therefore; Buy it, keep it clean with 99.9% IPA, and you will not regret it :-)

I'm using a new Creality Ender 3 Max Neo.**No need to apply the magnetic sheet**When I got my PEI sheet I was very apprehensive about applying the magnetic pad, which uses sticky adhesive on its backing to fasten permanently to the heat bed. If it didn't work as intended I would be stuck with a magnetic mat on my machine. It would very difficult to remove it, and clean off the adhesive (if at all possible).So I didn't use the magnetic sheet. I simply removed my glass plate and swapped in the gold spring steel PEI directly onto the heat bed. It's about half the thickness of the glass bed so I shoved a small piece of cardboard under each plate clip and it held snug. Of course, the bed needs to be manually raised a bit first to compensate for the thinner plate.To ensure that the PEI was laid perfectly, I positioned the printhead at all corners and the middle, measuring the distance with a sheet of paper (the paper should slide between the printhead and the plate with just a bit of resistance).Then I auto-leveled the bed.I have so far printed a dozen models, and they all held firm and printed perfectly.The best part... they popped off the PEI sheet with no effort at all. I didn't even need to remove the PEI and bend it.Bonus - not using the magnetic sheet allows the PEI to warm faster because it isn't insulated from the heat bed. And without applying the permanent magnetic sheet, I can easily swap back to the glass bed without the magnetic sheet insulating the heating process.After years of struggling with not enough adhesion, then way too much adhesion - it's a dream come true.

This is worth the purchase. I am just a hobbyist. But this has been great. Easy release for printing. Will need to add support material to print for prints with low surface profile or thin points of contact. Otherwise prints (especially pteg) can come loose mid print. That's not a problem with product but more user needing to consider print material properties.

Coming from using a glass build plate, NO MORE GLUE! when cooled the prints almost side off. When hot and part is done take the flex plate off lay it on my table saw table and watch the parts pop off as the plate cools. Just wish I would have mounted it over the glass plate for a more event bed heat. I may try and take the magnetic pad off and get a new one to put on my old glass build plate.

As a 3D printer newbie, I was getting frustrated with the activity as it took several tries to get anything to start printing correctly. My son recommended a PEI bed and it's been wonderful. It's easy to install, easy to remove and reapply and really helps in both initial adhesion and eventual release after printing. No more glue sticks!

I ordered this for my CR-10 S Pro, and so far it has been great. I have this bed on several other Creality machines they are inexpensive compared to other PEI sheets, the magnetic pad is adhesive-backed and is simple to install, and the adhesion is amazing. After changing the bed level sensor out, I needed a metallic bed so that the sensor would work with room to spare, so this was a no-brainer.

I really liked this plate but after use and cleaning as recommended I had a thin layer adhere so hard that it would not remove from the plate. I tried bending flexing, etc. The PEI actually came of the plate. I contacted the seller and we shared a few pics and they are sending a replacement plate for me. I get this plate may have had an issue but the seller is making it right! Hence the 5 stars and positive review. I look forward to working with them in the future!

Me funcionó muy bien en mi Ender 3S1, yo la prefiero que las camas lisas, nunca he necesitado adhesivos teniendo una buena calibración.

buena adhesión aunque me hubiese gustado que fuera mas lisa para que imorima la parte de abajo mejor como con otras laminas de esre estilo pero plr el precio vale la pena

Perfecto para la CR10S Pro V2, actualizacion necesaria para tener mejores impresiones y mejor adhesion, super recomendado!

Bought this to replace the stock plate from the Ender-3 v3 SE. The stock plate stated 220x220 right on it, unlike most of the other ones, so had to talk to support to confirm that the size would fit, at it does. We started having some issues (fingerprints/cleaning) with the original plate's adhesion so we decided we'd try another plate and keep our fingers off this one. It's been amazing, almost seems better than the stock one and has the proper notches at the top and grab tab at the bottom. Ordered a 2nd spare just to have one.Have ordered three of these, the last one was complete garbage, filament kinda burnt into the bed so bad I couldn't get it off. Swapped beds and print was completely fine... so it's the bed. Not sure if this was maybe from the bad batch like my original bed.

States it's compatible with ABS but then says the maximum temperatures it can handle is 200°C Nozzle and 70°C Bed, neither of which are hot enough for ABS, rather annoyed after I paid a premium for this which is no better than any other magnetic build plate for ABS!!