RLTechCase for Raspberry Pi 4 Model B, Raspberry Pi Heatsink for Raspberry Pi 4 Model B, Case with Fan Compatible with Raspberry Pi 4 Model B (Black)

Its a solid case and made with precision, fitting the Pi, heatsinks and fans took about 10 minutes. A little tip, it may look like the Pi will not fit - You MUST remove both end-caps, and slide the Pi in Power/Hdmi side first, If you don't do this, if fits perfectly. Also, look at the photos shown by the seller.. they indicate where to install the fan and where to plug the power into.This case comes with everything you need, including heatsinks, a fan... Personally, I've installed the Fan, but its not plugged in, as the heatsinks seem to do a good enough job (That may change).I'd definitely buy this again.. My only recommendation to the manufacturer, is perhaps include a paper slip showing installation.

With the current global shortage of pi4 3rd party cases, I took a gamble on this one and lost. I received a case with a microusb adapter that outputs at 3a (bizarelly enough the correct amperage for the 4) but was molded for a 3. End result: had to hot knife the new ports in and duct tape the lot.To make things worth the case is cheaply made, the fan cannot even affect the smoke from a single cigarette right next to it, and the list goes on. Avoid until the usual suspects start make proper cases for the 4.

Must say that I am very impressed. A very good case for Rpi4B (I have the 2GB model). It is usually around 46 ° C under normal use such as streaming movies from a NAS server or streaming youtube/twitch videos. I only use 3Volts for the fan to get it as quiet as possible cause using 5V on the fan made it pretty noisyIt is extremely simple and easy to mount and comes with heatsinks for all the chips and It also comes with a screwdriver. I used rubber dampening between the case and the fan so the fan wont transfer vibration to the case and make it more noisy. I really recommend this case. And you can see instruction on how to mount the fan and heat sinks on picture nr 5 and 6 on the page

I thought this was better than the other reviewer did - sounds like we got different products. I needed a Pi4 case and this is the only metal one I could find so soon. The threaded hole to fix the Pi board in place is in slightly the wrong location, so I had to drill out the corner hole on the Pi a little, otherwise all seems good. The heatsinks mount with normal 3m double sided film rather than a special thermal bond. The pi seems to be running a bit hotter than it was in the open air (at idle), but now it's physically protected and I haven't had thermal throttling problems yet. I haven't used the fan, the temperature seems ok for my 4 at the moment and the fan mounting 'design' seems to be to use some of the holes on the case to fix mounting bolts through, which wouldn't look great. There's no instructions, a shame since they would be helpful. Once assembled, it looks nice, feels solid, is great to have the Pi4 in a somewhat-ventilated metal case! I'll give it four stars given the low price.

Bought this for my new Pi4 because the first one wasn't good for the HDMI ports. This is a decent metal case, nicely designed to be just right in fitting. It was a little awkward to get the Pi in, as you have to get the USB/network side in first, then the hdmi ports with a squeeze, and then it is held with a single screw. And then it is ideal. Will be buying more for future Pi4's.

The case is shiny. With all the heatsinks fitted and the fan spinning my Pi4 remains cool under load.The opening for the SD card could be a little larger. Getting the SD card out is a little fiddly and I had to use a tweezers.The 30mm fan supplied with case is disappointing. It generates a high pitched whine that's quite distracting. I built an NPN transistor switch so I could control the fan with the Pi and only switch on the fan when the CPU gets hot. The Pi4 is being setup as a Plex media server so the fan still comes on a lot. I've ordered two 40mm fans and when they arrive I will replace the supplied 30mm unit.By all means buy the case. The next time I buy a Pi4 I will also get this case. But I will order a quieter 40mm fan at the same time.

I lost count how many times I had to unscrew this case and open it up just to get my MicroSD card after it disappeared into the bottom of the case instead of going into the slot. This alone means I cannot recommend this case. If this design flaw can be rectified in future editions of the case then it would be a decent enough product but not as it stands.

A really great case. Put together nice and easily once you've worked it out (read the other reviews to see how you should fit the Pi in).The fan was too loud for me, even on 3.3v so I've swapped out for a different fan. The case is great quality though.