Watts Premier Replacement Sensor Valve for 500800 500805 Recirc Pump

Not sure what causes this valve to stop functioning at same temperature differential as it does when first installed, but it only takes about 15 minutes to replace old one with new. Price is a consideration, but out of 3 valves, only one in the far guest bathroom needed replacing after about 3 years. Have not needed to replace the Watts recirculating pump, and using this system has consistently provided hot water just seconds after turning the tap on. Very pleased with this system.

The seals on the various ports decayed and ended up blocking the original unit from functioning. We really did not need to replace the original unit. In reality, we wasted our money. Poor design!

From the product details tab: “SIMPLE DESIGN: Equipped with two 12" supply lines with adapter fittings, this replacement sensor valve has a simple design that makes it easy to install and replace, requiring no additional components.” It does not include waterlines nor adapters. Very disappointing. I purposely bought this one because it APPEARS to be from Watts and I didn’t want to take a chance on a knock off valve (that also advertise that water lines are included) when it comes to my plumbing. What I got was a valve in a plastic bag. That’s it.

It works. Symptom: Very hot water circulating in cold line, not just warm. Solution: Replace Watts / Grundfos temp valve (this part). Result: Normal quicker hot water, sometimes a little warm water from the cold for a moment. Evaluation: Normal, all good. A few of suggestions: 1. Buy all new hoses. 2. Have tools ready to change the hoses - on the faucet too! Have a flashlight handy too! 3. Have a tray or bucket to catch water under sink and some towels you don't care about so much. 4. Turn off the house water valve, then open all the taps, espacially the lowest, to drain water. 5. BE PREPARED TO REPACK YOUR SHUTOFF VALVES UNDER THE SINK!!! Have a repack kit with new washer 6. BE PREPARED TO PICK OUT BITS OF OLD HARD SHUTOFF VALVE WASHER THAT PROBABLY CLOGGED THIS VALVE. 7. Clean it all, repack your shutoffs, check your hoses. 8. With good shutoffs at the under-sink, you can fix any minor leaks in your installation 9. Do this in working hours when the hardware store is open 10. Turn on, check for leacks, and BLEED air out of every tap. Bits of hard old shutoff valve killed my valve of the same type and model, which lasted about ten years. I hope that this one does better.

Works great. Wish I had replaced the other one sooner. The first one came with the instant hot water pump. This brings warm water to our upstairs bathroom in no time, saving us a lot of wasted water and the money to pay for that water.

The Watts Recirculating Pump delivers warm water to all your faucets for the time of day you choose. I've been using a Watts pump for a number of years now and I've learned if it stops working you may just need to change the sensor rather than replacing the whole pump. I was having my bathroom remodeled and the pump stopped working. I just tried replacing the sensor and I'm back in business. It's a lot cheaper than replacing the whole system.

First of all nothing is wrong with this valve. It does what it says it does. I give it three stars because...product knowledge is also helpful. So if you are reading this review I hope it helps you to make an informed decision. My house was built in 1992. With copper pipes and a BRANCH system water spokes off a main line and to the various fixtures around the house. I bought a Watts recirculation pump it was super easy to install on my hot water heater. I bought two of these valves and walla...I had HOT HOT water at the furthest points! How nice. I also had HOT HOT HOT water at ALL of cold water lines as well...not just the ones with the valve installed-all of them in the house. This was not at all helpful as then I had to flush the cold water for minutes to get cold water for just as long as I used to have run the hot water to get hot water. So basically I turned the pump off. I would use this product if you have a dedicated HOT WATER LOOP installed in your system so it pushes that water right back into the hot water side and not into the cold water side. I guess if I had used two wits in my brain I might have realized that before installing this system.

My instant hot water system was not working after it had been installed two years ago. Thought it was the pump but saw a Youtube video about what causes these problems. Changed out this valve and problem solved. There was a bunch of gunk built up in the old valve. Took about 10 minutes to replace.

Works great, Have used this for almost 2 years with no problems. My house has two sensors in the house, one in the kitchen and one in the upstairs bathroom. My only concern is continually supplied warm water until a check valve was installed near the pump (thermo syphon). This check valve should have been built into the valve OR indicated in the valve literature.

Originally bought the Navien navicirc recirculation valve as I had just installed a Navien water heater the water heater is great but the navicirc valve was horrible it howled like a cat in heat. Left all plumbing the same just installing the watts valve works perfectly very happy with my purchase. Valve on left is watts 1/2 the size of navicirc right

there is a grove that runs across each of the threads, preventing a water tight connection. The sensor valve that came with the pump kit did not have the grove and worked perfectly. When I received the items, I put teflon tape on the threads as I do with water connections. Unfortunately, that covered the groves and so I wasted 3 hours trying additional teflon tape and finally, plumbers paste. When I gave up and took the tape off, I realized why the connections leaked. This may be a knock off product as the original valve was fine.

Would be 5 stars but the price to quality ratio doesn’t meet anymore. Still does the job. Will see for how long

Easy to install and works great. Recommend