Pure Tone Multi-Contact 1/4 inch Mono Output Jack 5 PACK | Dual Tension Grounds & Dual Positive Tips for Optimal Signal, Tone & Lowest Possible Noise

I just resurrected a 90's BC Rich Warlock Bass (Platinum) using this jack, and a new jack plate. The wiring was done terribly on the original, and the original jack was just a single point of contact, generic junker you see in basically all basses and guitars. This thing was easy to solder, fit perfectly in the pre-existing jack port route, and makes absolutely zero noise plugging in. The connection is tight, and secure, and pulling this out accidentally is going to be a challenge!! For such a small price, and such a massive improvement, these things should be the new 'standard' for your gear. Soldering is cheap and easy. This jack is cheap and easy, and superior. I will now be replacing all of my gear with this jack. Unreal.

This is the second pure tone output Jack that I have installed. The first one I put in a kit guitar that I replaced a flimsy output Jack that came with it, in this one I put in an older Yamaha single cut with a problematic output. Output Jack. These are easy to install and work flawlessly. I highly recommend these output jacks for any guitar project that you might have!

True to its reputation, this Pure Tone output jack is a good looking well built TR 1/4” mono female connector. The quality makes it well worth the price. When it comes to guitar connectors, there are a lot of inferior jacks out there. I don’t risk buying anything except this dual-contact Pure Tone or a single-contact Switchcraft Jack. The Pure Tone connector fits well in my PBass guitar. The jack is made from a hard nickel plated copper alloy, Because of its thickness, it takes a little more time to get the connection tabs hot enough to properly solder in the wires. I found a 30-watt soldering iron to be sufficient. The insulators were unaffected by the heat. I Verified the dimensions: Mounting Hole Diameter: fits 3/8” hole Bushing Length: 3/8” Thread Type: 3/8-32 US-Spec Width: Approximately 3/4” Functionality; This Pure Tone Jack has dual spring loaded contacts for both the positive pole and the negative pole on the 1/4” plug. It fits the plug nicely and holds it securely. As expected, it does take more force to plug and unplug it than a single-contact jack. Even so, with my bad arthritis, I can connect and disconnect my guitar cable from it without too much difficulty. If you’re thinking about upgrading to a dual-contact guitar jack, spend a little bit more and get these Pure Tone jacks. You won’t be disappointed.

I love these Pure Tone output jacks - I’ve installed them on multiple guitars, and they make a big difference. They hold the cable jack much more securely, with a solid, stable connection every time. They fit perfectly in Firefly Les Pauls and are easy to wire in. Great quality, reliable performance, and well worth the upgrade.

Very nice output jacks. Previous jack on my guitar wasn't holding very well. Ordered these and won't look back. Fit is very positive and snug. Easy to install with basic soldering skills. Will be installing on other guitars.

I bought this input jack to use in a 2008 ESP LTD EC-50 - its a Les Paul single-cut style guitar with the input jack opening flush to the side of the body. No question that it is a durable, quality input jack and I love the subtle transparent black color - this is the primary reason that I bought it. I did consider the quality aspect, but it was mostly the color that drew me to it since the guitar I bought it for is all black. It works pretty well too - it almost has like a double lock feel to it when you plug in the cable. It has a quality "grab" to it and requires some effort to plug in and unplug the cable, which is also what I would expect. I had/have two issues with this jack; Its REALLY big and bulky and just barely fits in the input jack cavity hole. In fact, I am still having an issue with a short of some sort if pressure is applied to one side of the input plug on the cable; like the jack is pressing against the cavity wall shielding. The other issue is that you will need to rough the surface of the soldering points for an optimal soldering experience. This thing is big and busy as you can see by the picture(s). I had to solder the hot and ground for the pickups and the hot and ground for a kill switch. Not only was it super tight space I had to work in between all the prongs of the input jack itself (outside of the body), but it was a nightmare getting the solder to weld to the surface based on an inability to solder to the bare metal connection points on the input jack. I had to scratch the whole thing up with a tiny flathead screw driver with a piece of sandpaper taped over the end of it. It was very frustrating. Overall, I am happy with it but if I'm being honest, its still the color that was the reason I bought it and worked with it as long as I did to make it work. Otherwise, I would have just used a Switchcraft or AllParts input jack. Input Jacks aren't magic...as long as they are not made with cheap, thin metal, the connection prong is not bent out of sorts and the solder work is adequate, pretty much anything will do. I'm not sure if I would buy it again or not (unless I needed one that is black, then I would for sure). It's reasonably priced and it is a quality part, but there are so many other options that I have used that are similarly priced and so much easier to work with.

Easy to install. Rock solid connection. You can totally feel the difference when you plug-in.

great upgrade for any guitar, would recommend this to any guitar player having connection issues like myself.

I bought this thinking I could fit them in my bass guitars which have active preamps... they don't work in them. These are only for Passive instruments. Having said that, the build quality on these is amazing. If you have passive instruments, I highly recommend them.

Buena calidad

Nu är det slut på irriterande glapp i kontakten!

These are amazing. Swapping out all my old, loose guitar outputs with these. I don't wire the extra contacts, just use them to hold the cable more secure and keep them from wearing out as fast. Makes for a SOLID connection. Highly recommend.

much sturdier output jack