ELEGOO 6PCS 170 Points Mini Breadboard Kit | Breadboards for Electronics Kits, Arduino, Raspberry Pi

Brilliant. I purchased some cheaper ones from a well known online marketplace and I found that the connectors would bend as I inserted them into the breadboard. No such problem with these. They are perfect for building small breadboard electronics projects, and the size is great. Nice clear colour markings too, and great value for money.

Works as you want it to, it's a bread board. Just just dont try cutting bread on it.

I found these boards to be very good. They are accurately made and fit together. The only problem is that the adhesive backing masks the slots needed to clip them together. Removal of the adhesive around the slots with a scalpel or sharp knife is all that is necessary. They are useful for general work and not just Arduino.

An old fitter once told me, “when it comes to tools, you buy cheap, you buy twice.” And that’s something that’s stuck with me because every time I try to work in a budget, something invariably goes wrong and breadboards are no exception. I’ve had a few over the years but this is my first Elegoo - an Amazon recommendation. I’m working on a couple of Arduino (clone) projects at the moment and a breadboard is the way to get things working in a hurry - or at least, it should be. The problem (with the cheap ones) is this — the sockets are stiff and often have unreliable connections. This results in two things:(a) a lot of loud cussing because the fine leads on components like small resistors, jump leads and many other small components bend as I try to push them in. This can be exceptionally frustrating. (b) worse, when the connection fails, so does the circuit, but then it can be anything from tricky to a virtual impossibility to figure out what is wrong: is my design off somewhere or have I put a lead in the wrong hole? Finding it’s nothing more than a failed socket is enough to bring tears to your eyes when you’re up half the night trying to find the fault which was no fault of your own. Other than trying to save a few quid on a BBB - a Bargain Basement Breadboard. And yes (a) has happened recently and it was fortuitous that Amazon recommended these and our of desperation, not to mention sore pinkies from fiddling with overly stiff sockets, I took a punt. When they arrived they looked just like every other breadboard I’ve had - that was until I tried to put a clone Arduino in there and oh boy, those sockets felt tough. My heart sank a little but it’s new, so I figured they’re just a little tight and breadboards are not ideal for such large pins, particularly when you’re trying to put 30+ in at one press! Then came the acid test. How hard is it going to be to mount a discrete component in there. First off, I tried an LED. In she slipped, buttery smooth and fitted like a glove. Perfect fit, both leads, first time with very little effort. Nice. Now some Dupont pins (Elegoo also available on Amazon) and in they went - first time, smooth and with very little effort. 1/4w precision resistor - with fairly delicate leads? Dropped in like a champ.Very occasionally I did find that some holes were a little tight but that’s more about my lazy attempts at not centering the component before trying to insert it. Compared to the BBB this was like going from a 1* B&B to a 5* hotel! It was only at this point that I noted another (small) but interesting departure from my other BBB... the power rails feature slightly larger sockets. Again this sounds like a “so what?” but you can tell some thought went into this as the power, ground in particular on audio circuits and many digital designs, carries a fair amount of current and larger pins means lower resistance which means less hassle. Sweet! I’m starting to fall in love with this. For larger designs, most breadboards can be connected and this one is no different, but careful attention to tolerances has ensured that it’s possible to stretch fairly large HATs (Hard Attached on Top) across more than one board. Considering the tolerances involved this is quite a feat and I’m grateful for both the locking mechanism and the very sticky pad which held tight to the surface of a scrap piece of “hardwood” flooring. It will take longer to determine how robust these boards are but my initial impression is that they are built to last and should give a long service life. Unlike, it has to be said, my BBB which I’ll be donating to one of the apprentices just to tease them. :) Photos show the slightly larger power strips and a BBB with an Arduino clone vs. the Elegoo hosting another Arduino with an AZDelivery resistive touch screen (available on Amazon for the Uno).

I missed the fact that there were 3 pieces to a pack, so I now have 6. Value for money is amazing. I am putting 2 of them to good use and I very happy with them.

exactly what I was looking for. Bought a clear breadboard but it was very difficult to see the sockets to plug in components. The white breadboards are so much easier to use. Bought these for use in a local coding club so need to make sure it is easy to get the circuits correct.

Nice and sturdy for the price. all connections work.

I was almost put off purchasing the Elegoo 3 piece solderless breadboard after reading numerous one star reviews but decided that at the price I would try for myself, I'm very glad I did. I've been struggling with my existing board which is extremely tight and very difficult to insert anything into. The Elegoo boards make it easy to insert even the most delicate resistors with ease. I would definitely try this make in future based on my experience with this product.

Super

Les breadboards sont de qualité correcte. Les pads adhésifs à l’arrière gênent l’emboîtement ou le retrait des barrettes. Fonctionnels, mais pas très modulables.

Come lo stesso articolo aquistato precedentemente, niente da ridire, tutto okay

كمبتدئ يمكن تشتريه وتحسبه بالحجم الكبير، بس انتبه، ترى الحجم صغير

Bonne qualité générale, certain trous sont parfois récalcitrants mais rien de grave. On emboîte plusieurs planches ensemble de façon solide. A noter que ces planches n'ont plus rien à voir avec celles que Elegoo faisait il y plusieurs années (qui elles étaient très mauvaises), il y a eu des efforts à saluer !