REEKON M1 Caliber Measuring Tool for Miter Saws – Eliminates Need to Measure & Mark Materials, Reduces Cut Time and Increases Safety, Measures Flat & Round Materials

I wish I had this 20 yrs ago. It's fantastic. easy to calibrate. I wasn't sure about a few things but once I calibrated the kerf every cut is exactly what I cut. Clamps on easily to the fence. Super easy to read. Comes with a nice case to keep it safe when done work. I normally don't leave reviews but the reekon m1 is every carpenters dream. My nephew builds cabinets and when he seen mine he ordered one while I was doing a demo for him....buy one......thanks reekon for a great product Tom Zimmerman

This is a fantastic item. I purchased it with the Reekon T1m digital tape for building honeybee boxes and equipment. I use the M1 for all the smaller repetitive cuts. It is extremely accurate for cutting multiple precision like length pieces. Important when dealing with 1/4 Inch bee space. I have since found many uses for this item cutting pieces for projects around the place. It even works for measuring miter and bevel cuts. I find myself looking forward to opportunities to go use it. I am extremely pleased with this purchase.

This just changed my game with woodworking. My cuts are perfect now. Glad a coworker recommended it to me.

I'll give you all a moment to stop giggling The Reekon M1 is one of a few items over the past couple years that I saw used on Youtube that turned into a serious game changer. ====> AS LONG AS YOU SET IT UP AND CALIBRATE IT PROPERLY! <==== Make sure to verify that your blade kerf is set correctly in the M1 or every cut will be slightly off. I have a Bosch GCM12SD Miter saw and quickly found out it was not immediately compatible. My fences don't have a proper spot to clamp onto so I had to purchase their adapter fences and mount them first. Annoying yes, but not a deal breaker. In reality i maybe could have researched that but I was a bit too excited. Either way once you get the blade kerf dialed in and your first calibration cut out of the way, you are on your way to perfect repeatable cuts. Its also super portable, I brought it with me to my Brother-in-laws and mounted it on his Metabo miter saw while helping him build a fence. Pros: Easy to read display, super accurate, vastly speeds up my cut lists, and comes in a nice foam storage case. Cons: For the cost they could have included the 2 AA batteries needed, make sure the piece you are cutting doesn't have major depressions or knot holes in the path of the measurement wheel ( the wheels distance traveled will be different from the straight length ), and you may not know if your saw is 100% compatible until you're there with the device in hand

This product is awesome.

Not worth it in any means my friends. There is no substitute for a good tape measure or a jig type set up . The roller pics up dirt on the boards and everything else. I tried this thing every way I could and it did not give me an accurate measurement in any application i used including there step by step instructions or videos on this . There needs to be one using a laser measuring system but , this Would defeat the value. I would say it would be best to make a stop jig set up using old fashioned Know how and wood . But , for this thing, do not waste your time and money like I did would be Very good advice

I was attempting to trim 3/8" off the end of a board and after 4 attempts, I got a piece that measured 3/8". Two of the pieces were narrower and the other was wider. It wasn't off by much, but it was off. Here's the issue when trying to cut such a short piece...there are multiple ways to get to 3/8". Method #1 -- slowly slide your stock under the wheel until the readout says 3/8". Stop there and cut. Method #2 -- slowly slide your stock under the wheel until you are past 3/8", then slowly slide your stock back until the readout says 3/8". Stop there and cut. Method #3 -- slide your stock back and forth while the readout is showing 3/8". Work back and forth until you feel your midway. Stop there and cut. Each approach gives you a different result. When I did get 3/8", I couldn't tell you which method it was, but it was #2 or #3. Two more issues: 1. The device also slips off my fence quite easily, but maybe that's my miter saw. 2. I originally set my blade kerf to 1/8". After getting some off cuts, I tried to change it to what I actually measured it as - 7/64". I went through the blAde configuration, rolled the wheel, stopped on 7/64", and pressed the zero button. The display goes back to saying 1/8". When I go into the configuration, it still says 7/64". So even though I am setting the blade kerf to 7/64", the offset being used when I zero my stock is 1/8". I have no idea which number is actually being used, but this inconsistency doesn't help with accuracy. I have gone back and tried this a few times, but I end up back using a tape measure. Too late to return it now.

I seldom do reviews to get one you have to be really good or really bad. I purchased the Reekon M1 to use on my sawmill for the vertical movement of the saw and it worked perfectly in spite of not having been designed for that application. It also works well on my miter saw as it’s intended to. Then after a couple of years it refused to power up knowing that warranty's don’t last forever I contacted the company to see if they could repair it before ordering a replacement. After a few emails to troubleshoot the problem they sent me a replacement unit. Long story short this is a tool that works well and is backed by a company that believes in its products and supports its customers.

Very first delivery and Trust quality

Ürün çok hızlı ve zamanında elime ulaştı ama 100cmde 5mm. 150cmde 10cm 200cmde 17mm fazla ölçüm yapıyor acil yardıma ihtiyacım var,ürün hatalı mı yoksa ben yanlış kurulum mu yaptım destek istiyorum

Fungerar utmärkt

dit is een echt top product, je hoeft net meer te meten zolang je maar alles correct volgt zoals beschreven. ik gebruik het nu dagelijks bij mijn afkort zaag op de werf aanrader voor iedereen in de afwerking

Premessa fondamentale: se non sapete calibrarlo inizialmente non lo guardate nemmeno. Detto ciò, il prodotto va calibrato e la precisione spiazza talmente è accurata. Si può usare sia a dx che a sx della lama. Io per il modo in cui taglio alluminio ho dovuto creare una staffa che mi portasse la rotella più vicina alla guida di scorrimento. I materiali sono super robusti anche se in plastica. Se devo trovare una sola pecca è il manuale di istruzioni in inglese, ma c’è il qr code per andare sul sito e tradurlo in italiano. I soldi spesi ci valgono tutti. Lo consiglio tantissimo