AnchorFix-2 Super Strength Anchoring Adhesive - Two-Component System for Threaded Rods in Concrete, 10.1 fl. oz - Fast Curing, Solvent-Free, High Load Capacity

Anchored wrought iron railing in 2 places with no problem. Set very quickly. No drilling into the brick. No problem

I had a cheap HF gun which couldn’t hack it, luckily my BIL had a very good one and that delivered the product just fine. It sets pretty fast even at 50º ambient but things can move for a while if not attended to. I set four 4x4 post bases that have a 9” rebar welded onto the bottom in a rock bald which was grey shale, it did not scale or shatter when I drilled it and remained very solid. I used a 1” bit to give me some wriggle room alignment wise, filled the holes 3/4’ full and pressed the bases in, a good bit flowed out the top as I set them. Over the next hour they shifted slightly and went out of alignment a tad but I coerced them back into place. They will be supporting an 8’x6’ covered porch so I probably didn’t need adhesive at all, the weight of the porch being what it is. The recommendation for a 3/4” post pin is a 7/8” hole but I didn’t have a 7/8” rotary hammer bit, only 3/4” and 1”, so 1” it was. I cut about 2” off the end of the mixing nozzle but didn’t cut back to the point where the mixing labyrinth is. I pumped out about 6” of product on a paper towel but should have done more, the gun wasn’t cooperating, by doing more it insures that only well-mixed product goes in the hole and more importantly stays in the nozzle - many people have trouble with the nozzle clogging but it’s often because they failed to follow the instructions on the tube imo. A high quality and high power caulk gun is mandatory imo.

This adhesive works great for securing anchors in concrete for installing my two post lift. First off this is hard to ouch thru the tube. I bought a powered caulking gun just for this job. With an assistant following me I was able to fill as many holes per tube with them inserting the bolts behind me. Does it setup fast yes does it hold tight yes. Torqued bolts t 120 ft pounds with no movement.

I will take some ownership of this issue, but honestly I wasn't dawdling that long. I had four bolts to set in a wall. Pumped in the epoxy for the first and was a bit slow putting in the bolt. By the time I was working on the second the epoxy had already set up in the nozzle. Switched nozzles and managed to get #2 done but that was it. This stuff holds, but sets quickly.

When it says, FAST SETTING, this is true.... It dried rock hard in about 3 minutes. In fact, it's too fast for my specific application. I need a bit more time to work. I had to re-drill the hole to drill out the adhesive. So if very fast set and rock hard is your need, I suspect this may work for that.

Sets up in minutes. Has a slightly gritty texture that looks like textured concrete. As it mixes in the nozzle, it will also set in the nozzle, so work fast and keep the flow going. Used to set 48 loop anchors so have everything drilled and ready to go before adding adhesive and anchors. I used both tips to set all the anchors, then used the balance as infill and texturing. Just eject some on a paper plate and mix manually. Good stuff from Sika !

Seller must be distribruting old expoxy. We had literally the same issue as another guy. We used our best heavy duty caulking gun and it would not even exit the tube! I'm saying this is true: "I followed the instructions, removed the cap, cut the bag below the clip, inserted in a caulking gun and started to squeeze out a little to get the mixing started. Literally 10 seconds or less later tried to squeeze into the hole I had pre drilled and it was already hard in the mixing tube. I cut the nozzle back 3 inches and it was still too hard to squeeze out, broke my gun. I tried the second nozzle and another caulking gun and got one hole filled before the epoxy was hard in the nozzle again. Decided to open the whole thing up squeeze out the epoxy on a board and give it a hand mix..." Clearly defective product. Buy it from a box store instead.

My Husband wanted to try this to help with a gate that he put up and in the cinderblock and I don’t know all the details but it’s been some months now and it’s done it’s job wonderfully!

Seems very strong but way too fast to cure I put it in the fridge but product is very hard and comes out very slowly. When in the concrete cure in one minute or less. Won’t give you much time to install carefully the bolts