Question 1

How do i apply material

Accepted Answer

I've used this on several guitars (including mahogany, spruce, padauk, bubinga). After sanding, I apply any stain I might want. Usually, I just use Minwax natural to add depth with not much color. I follow that with a coat of Zinsser Wax Free Seal Coat, diluted 50:50 with denatured alcohol. After a light sanding I do 2 or 3 coats of Aquacoat, using either a motel keycard as a spatula or just rub it in while wearing nitrile gloves, making sure to wipe off the excess to minimizing sanding. After it's dry, I lightly sand it, looking carefully for any spots that had build up, and finish it off with a dozen plus light coats of aerosol Deft Lacquer (gloss of your choice).

Question 2

If this has a jello consistency, how will it stay in place when applying it to my upper cabinet frames?  Won't it run off a bit?

Accepted Answer

Yeah, it will stay in place in a vertical application. Even upside down.  It's way thicker than Jello. More like vasoline once spread.  Once any stain or sealer is applied, I add a coat of gloss finish.  Then, you can really see the pores or tear out your trying to fill.  Add a the aquacoat, let it dry (20 minutes or so), sand, and repeat a few times.  Then, proceed with finishing.  Works great.

Question 3

I have old polyurethaned oak cabinets.  Do I clean, sand prime cabinets first then apply aqua coat or is the process reversed?

Accepted Answer

The most successful process for refinishing your cabinets with Aqua Coat Grain Filler would be as follows.
   1  We highly recommend you do this process completely to the end on the back of a drawer to help you assure success. 
   2  Sand with 220 grit sand paper.  Wipe down with a dampwater paper towel or old t-shirt. Do not use tack rags. they  contain oils or wax
   3  De gloss
   4  On your sample drawer back, apply 2 coats of Aqua Coat Grain Filler with a credit card. bondo blade, rag for curves. Lightly sanding with a 320-400 grit paper in between coats.  You are not sanding it down, you are not sanding it off, the only reason you sand is to form a better bond between coats. Only sand immediately before applying the next coat.
 5 for testing purposes On half of this drawer back apply a third coat. When you have completely gone through the testing process you will be able to decide if you need 2 or 3 coats.  Lightly sand 3rd coat with 320-400 immediately before applying primer.
 6 Apply 2 coats of a high build primer water based, oil based, solvent based
 7 Apply 2 coats of a quality paint. water based. oil based, solvent based

To save an immense amount of time we highly recommend going completely through the testing process to see if you need 2 coats or 3 and  have confidence in your process.

Question 4

Have you had any problems when filling in deeper gouges or chip out?  I have used another product and it left the areas white when it dried.

Accepted Answer

If you left areas white then you applied it to thick. It is a pore and grain filler. Not a deep gouge filler. If you would like to touch up deeper indentations add a little sawdust from the piece you are working on to the grain filler.

Surface Recommendation	Wood
Material	Water, Oil, Solvent
Item dimensions L x W x H	12.1 x 12.2 x 10.9 Centimeters
Item Weight	998 g
Liquid Volume	1 Quarts
Manufacturer	Aqua Coat
Global Trade Identification Number	00748252493514
UPC	748252493514
Country of Origin	USA
Item model number	300-00-02-1
Product Dimensions	12.07 x 12.19 x 10.92 cm; 997.9 g
ASIN	B00LEFQEQE

Aqua Coat Clear Wood Grain Filler Qt

Detalles

Descripción

Presupuesto

¿Tienes una pregunta? Mira lo que otros preguntaron

Preguntas comunes