Atlantic Maxsteel 12 Tier Shelving - Heavy Gauge Steel Wire Shelving for 864 CD/450 DVD/Blu-Ray/Games in Gunmetal,38408071

For the $$, no complaints at all. Fairly easy assembly. All parts quite sturdy. No “bowing” of shelves, fully loaded with DVDs (books might be another matter). The clip-in dividers work very well, lock in and don’t move. The “footprint” is narrow, so some way to anchor to the wall advisable. Fairly stable even without anchoring, though. Would recommend, and would buy again.

It's great, sturdy, tall. It holds a lot of DVDS. It's heavy duty. It's sturdy. Anchored it to the back of the wall. Great price! Once together it's easy to move it. Just glide it to where you want it. It does get heavy if you don't have it where you want it. It does exactly what I wanted it to do, is hold alot of DVDS. All the parts were in the box. I would buy this again.

Good quality shelving. Easy to assemble and looks nice. I've had it about 4 months and no signs of shelf sagging or other problems. As would be expected due to height and narrowness, there is some wobble when moving items on upper shelves (especially with heavier cd's on top like I have it set up). For sure you'll want to attach it to the wall with included bracing straps to avoid any accidents (important if you have kids or pets around!). Also purchased the 5 shelf unit to pick up the "overflow" media. An equally good product.

The media could not be loaded. These are professional dvd racks. Fits dvds and games perfect. Stability. is high quality. Performs as it should. No missing parts. Lightweight. Good value. Also makes a wonderful gift. I bought 4 racks As I am a collector. I recommend this product to anybody Who's looking for a professional look.

I bought two of these and have them filled with primarily DVDs/ some blue ray. This makes it very heavy and will bow in the center it’s just inevitable. I didn’t want to add a brace and it look weird so I used blank dvd cases and placed them on the cross support wires that run front to back and that allows all my DVDs to slide in and out with ease. Some box sets are a tight fit unless you increase your spacing which will reduce your amount of DVDs to display. Given their height I highly recommend you add the supports provided at top and middle so they don’t fall on you. I used black two hole c pipe brackets at several spots down main supports. They aren’t going anywhere. They look great and display all my DVDs perfect. Some people have noted the feet are not sturdy and broke easily, but I did not have that issue. There is a YouTube video of a guy who made sturdy feet for these and I was going to do just what he did if I had his issue. Just put the product name into YouTube and it pops up as one if the first videos. If you’ve read this far and have a huge collection. These will solve your issue. The only pain is counting notches to make sure you have all 4 corners at same notch, but that’s the only issue I had . Best of luck

Very sturdy. I bought it so my husband would whittle down his DVD collection. It almost worked, but the shelf is terrific!

I bought 3 units to replace a WOODEN 3 shelf WIDE unit. shortly after the wooden unit was assembled, had problems. the shelves sagged severely the paper thin hard board back bowed out-- trash. it looked bad too.this product: material, steel, excellent ---ease of assembly, very good--- (see tips below) capacity 70 cd cases to a shelf*--- leveling pads, best I've seen! pads are very wide with a TEMENDOUS length of thread bolt for leveling adjustments. Each shelf has a full length "stop" bar 1/2" tall to prevent media from falling out the back.tips:1. instructions say to combine two rods to make 1 long one. For easier assembly to start, I say DON'T.2..Attach leveler pads to bottom (tapped) rodsHey! you're working from the bottom shelf up! SHELF IS ON ITS SIDE, NOT FLAT!3. working from the tapped hole end put the two piece shelf stopper on the bar and pull it down gently until it stops in a groove, you'll hear a click in place. Place one 2 piece joined stopper at the SAME groove height on EACH of the 4 bars.4. place the 4 rod tops through the shelf corners from the BOTTOM of the shelf. Once first shelf loosely is on its stoppers TURN UNIT to where the four rods are vertical (straight up)5. press shelf down gently to where shelf fits over the shelf stoppers evenly6. repeat 3-5 for each shelf. (once you have 2 shelves in place the rack becomes far more easier(solid)when you get close to top of the tapped rods, THEN put on the 4 top rod to complete the unit, continueshelving until done*Storing music alphabetically, by genre, I left a gap for future growth, .placing 60 cd's per shelf 2-1/2 racks will hold 2000 cd's