Adamson B10 Gray Bed Cooling System - Twin 75” L x 39” W - New - 100% Cotton Mattress Cooling Bed Pad for Night Sweats - Water Bed Cooler Ideal for Hot Sleepers

Oh My God! This feels so good! So I selected this model for the price and that it seemed like it was not loud. (It is not loud). Also because I felt it would not bother my wife who did not need any cooling. She was tired of me running the fan overhead. She did not like the breeze. But I was a little anxious because one commentator had said the covering had a top side and a bottom side - which would force the user to place the cooling unit attached to the mattress cover to one particular side. But after examining the mattress cover, the thickness of the material is the same on either side. Though one side did kind of seem softer, I think that is because of how it had been rolled up or something and not a real difference in the sides. Which was great because I did want to use the 'back' side as my up side so that I could place the cooling unit on the left side of the bed (or the right side if you are at the foot of the bed looking toward the headboard). Also, though the directions recommend you place the unit above the mattress topper during operation, there are also extra directions for how to place it lower than the mattress topper if needed. My other concern was that the tubes in the mattress topper would bother me. I get bothered by the smallest crumb in my bed so I wondered how it would work. Well not really a problem! I slept better that first nite than I had in a long time. I do notice the tubes on my heels and so I tended to move my legs around until my feet were positioned in between the tubes for comfort. A small drawback really. Also the directions say you can add a mattress topper on top of it if you want to. This will reduce the cooling effect. However this will not be a problem for me because there are quite a few settings and I was on the lowest setting and it worked great! The lowest setting is just to have the pump on and not the cooling fan. So the water circulating through the topper was all I needed. I will try a comforter over top it tonight to see how it does since I did have to adjust my feet more than I wanted to. But I am not worried it will not be cold enough because there are 4 fan levels to use, not to mention even two settings where the fan will run for a short time and then stop for a short time as an in-between temp setting for the pump only and the slowest fan level. Wish I had known about this product earlier! I will mention that the plastic used is not the most robust. It does seem pretty cheaply made - but I picked it because it was not that expensive. I don't feel like it is going to break right away or anything. I think for what is does the price is quite good. I really like that there is a remote. You do seem to need line of sight however to use it.Update: Still working for me, I did put a thinish comforter over top to make the tubes less obvious, and that did increase the comfort level, though I would not say it is a requirement for everyone. Also I spray a little mold killer into the unit on a regular basis as I don’t plan on trying to deal with a monthly regiment of draining and drying.

This machine works great if you are a hot sleeper, there are other units out there that have more versatility if you want to pay more money. (Chillisleep is 8 times the price)But this one has worked great for me for years! The negative reviews are people who do not properly do maintenance!! First off you must put a drop or two (at the most) of bleach in this every couple of weeks.Once a month, I unhook it and take my machine to the kitchen sink and empty it, put some hot water in it (swoosh it around) to clean it. I also have a compressor in my garage that has a very long hose with a nozzle on the end of it to blow out air. I take it into the bedroom and after I have unhooked my machine, I use a bucket and I blow the remaining water that is in the tubes into the bucket. this cleans out the tubes on the mattress pad. This maintenance routine seems like a lot of work, but it really is not and I have used and kept my machine running smoothly for years.It truly works wonderfully, and you can dial it down to the point that you feel like you’re sleeping on an ice cube. I just wish I could get a hold of the people who designed it to make a couple of minor adjustments that I think would be way easier for maintenance.

This mattress cooler has more leaks than my colander. It leaks in the back and in the front. The pad is very uncomfortable even with a mattress pad over it. It does cool the mattress though. I just can’t recommend it.

Constantly waking up at night due to being too hot was getting old. My first night trying 9/29/2024 gave me a really good night's rest. The lowest setting got too cold but it was great. Used my sheet and light comforter and it was WONDERFUL. Took me 5 minutes to set up, waited the 20 minutes for the water circulation into the pad, laid down and was happily surprised. I did cut a small hole in my sheet because I wanted to lay on the sheet versus directly on the cotton pad. I have a skinny nightstand and then a chair next to my bed and opted to put the machine on the back of the chair parallel to the wall just for more even flow of water. When I woke up this morning, I refilled to the 3/4 area so it's ready when I get off work. It does make noise but no more than my fan sitting on my dresser which I still use and a stays on 73 so others in the house don't freeze. I'm 55 (peri menopause), 5'9" tall and weigh 160 and workout daily. Not overweight but hormones are real :-). Will buy a second unit for my she-den which has a daybed where I might fall asleep watching TV on the weekends.EXTREMELY HAPPY SO FAR!I DID NOT WAKE UP SWEATY!VERY GRATEFUL!!!