Internal Backwater Valve,4-F 4" Float Model Flood-Guard for 4-inch Flood Drains,Drain Backflow Preventer for Sewer Flood Protection

A+. I deal with basement back ups when the city streets flood. Sump pump is fine, storm sewer is issue a backflow valve in the yard would cost thousands to install. This worked great so far in my basement. Last time I would’ve had an issue it barely let any water seal past the gasket edges. Usually I’d have 2-4” in the basement under these circumstances. I can probably tighten it a little more again, but it was very tight to begin with. Hold it with 1 hand and start screwing the 4 screws in a circle. Once snug you can crank it tight. Lean edges as best as possible. Mine was cast iron so hard to clean. Fit well. Works well. Also best one I’ve seen to allow water to go in, and not clog it up.

This is excellent. I replaced one that I had for years but corroded. The key to using these is to put it down into the PVC tube just far enough that the center "pin" sticking up is about 1/4 inch below the level of the floor. This is made well, is a quality item, and is easy to install. I may buy another one so that in 20 years when this one is all nasty, I can replace it easily.

The 2" model is a much poorer design than the others. Because it uses only 2 screws instead of 4 it is very easy to accidently get the rubber O-Ring misaligned and then you have to start the whole process over again. Be very careful when inserting this and tightening it to get it perfectly straight in the drain! It comes fully tightened and will not fit in your drain in this config. You need to almost fully loosen the two side screws. The O ring will then get sucked a bit into the sides of the device. The main problem however is that the spring is simply WAY too strong. I suspect they used the same spring and design from the larger models which would have much more water on top compressing it down. To make this work you will need to: 1. Cut a few coils off the spring. This depends on how far down you can insert the device (farther is generally better as there will be more water weight on top to open it). Make sure you are ABOVE any kind of standard P trap! 2. Once you cut off coils from the spring the spring will now not go the full length of the screw. You need to buy some very small washers to fill this gap. 3. Tune the tension of the spring and the amount of washers with the device MOSTLY tightened. As you tighten the device it changes the length and therefore the amount of seal the float will make. If you decide on the amount of washers when it is fully loosened you will be in for a bad time when the float now no longer seals via the spring. I used in total about 5 washers after a lot of experimentation and I cut maybe 4 coils approximately off the spring. I tied a small string to the middle bar of the device in two places (on either side of the screw) so I could lower it evenly. Make sure to carefully tighten each side evenly and if it gets at all misaligned / angled within the pipe start over. If its angled then its not going to form an air tight seal. I also put lasco pure silicone grease over the O-Ring and the float to make sure it sealed better (only use pure silicone grease). And make SURE you lean the crap out of the inner wall of the pipe you are lowering into - I used a wire brush. I was only able to insert it a maximum of about 8 inches down but this setup now works great for me. No more sewer gas smell and hopefully no more backups!

This device has saved my basement twice from being flooded with several inches of water. On two occasions in the past year, we received heavy rainfall (4+ inches). While several neighbors had their basements flooded with inches of water, I only experienced a small trickle due to dirt/debris on the rubber plunger. A couple of recommendations: Get a tube of silicone grease and apply it once or twice a year to the rubber seal to keep it from drying out. If it dries out, it may not form a good seal when floodwater comes up. I also highly recommend a water leak sensor that sets off an alarm if water starts to rise and bypasses the valve.

This was easy to install but the seal failed. It looked good but water was coming around the flotation device that was supposed to prevent back flow.

My son had to go to the hardware store to get new screws cause the screws that came were stripped are poorly made he had to spend money

It does require you to cut the spring down if you want water to drain. The spring it comes with is pretty strong, and would require several inches of water to drain through it. I cut it down so that it barely seals. I bought a house where the basement had flooded from a back up of the city lines. I installed this in the basement floor drain after it happened to me and hoped for the best. I wasn't sure if it worked, but a year later I ended up having another back up, except it came up through my basement shower drain (being the next lowest point). The good news is that all the black stuff stayed in the shower pan. I'm buying a 2nd one for the shower now, and I'd like to think the toilet won't be the next place to back up. If a couple years go by and there's not another back up, I'd love to refinish the basement.

Fit great

Everything else I could find for this size range is simply not performing up to the expected degree. This one does the job and does the job well

I purchased the 3" version and it fit perfectly. I saw reviews saying they could not control the water going down. There is nothing to adjust really on this. The 4 screws around makes the rubber expand the form a solid seal inside the pipe so that it cannot just be pulled or pushed out. The middle screw should not have to be adjusted. The water goes down with weight. If you have a cup of water it will not go down so press the button and down it goes but if there is a bucket, the weight pushes it down and allows it to drain. Hope this makes sense. For me, it works perfectly and what I needed. I installed one in a garage drain and now will order a second for the laundry room drain. Depending where you are and your situation, you could use these instead of putting a main one where you will have to dig. In my case there are only two small drains in the basement so it makes sense.

Solide et facile d’installation J’ai du réajuster la sensibilité mais tout semble parfait

Very easy to install in my 3 inch PVC floor drain but the protruded spring pin is too easy to be bent such that you'd have to install the set way below the floor level, a little harder to fix the screws

The 2" model is poorly designed.