Dmax Heavy Duty L Brackets White Steel 6" x 8" | 3 Pack | Hidden Countertop Support Brackets | 3/8" Thick, Holds 150 lbs | Floating Look for Granite, Quartz, Wood, Concrete - White

Very please and surprised at how well they've held up compared to the outrageous prices the granite store was charging; plus these were thicker. Very very easy to install.

I counter-sunk these onto some backer board that I installed behind the drywall of our half wall waterfall edge bar top. Everything about them is great. The only modification I made was to measure and drill countersunk screw holes on the surfaces the bar sits on so that I could screw the bar down to the brackets themselves (instead of using a cement). The reason being that we used a finished wood rather than granite or quartz.

They're solid, heavy, and look nice. they have a low profile but still visible. if your goal is to have large decorative corbels or brackets these may not be a good choice. Other reviews had mentioned issues with being "square". I did have some very slight variations (prob 88-89deg if I had to guess) but this was easily solved by placing a small washer on the back side of the lowest screw hole and that counter levered the bracket enough to create a snug fit. Another trick if you are installing these after the countertop is already in place is to install the top screw first and at a slight upward angle. This will pull the bracket tight against the underside of the counter. Finally, they come with screws that recess nicely into the holes or you can get wide flange ones from a big box store that settle on top of the hole for a more rustic look.4 stars due to slight variations in product being square and finish will chip easily so be careful. Otherwise theyre great and I would buy them again

I ordered this product in the 4 quantity and needed 2 additional pieces for the project. I did not see an option to puchase less than a pack of four from this supplier. I ordered the 2 additional pieces from a different provider on Amazon. There is a notable difference in the finished appearance of the products offered by these two suppliers.This product, in pack of 4, has smoothed edges to a degree where they pose no risk of injury should someone brush against it with their leg while wearing shorts. This is important to me as I am using them to support a granite counter top with a 10" overhang to allow for bar stool seating. I found the 90 degree angle to be accurate and consistent. The screws provided with the product match and fit perfectly. The angle bend in the product is smooth and slightly rounded which allows for a more finished appearance. The inside of the bend has a small, smooth weld.The other order of 2 pieces is less "finished". The edges are pretty sharp and I will need to round them, the inside of the bend has a larger weld line that is not smoothed. The angle outside edge of the bend is square and the dimensions of each measurement are slightly smaller than the other product.Having both products to compare left me impressed with the attention to detail on this suppliers product (Pack of 4).

Great product. The are very rigid with an industrial grad feel. They came with the heavy duty screws and the #3 Phillips bit needed for the screws.I bought this product to support an 18" granite counter top that sits on a raised bar of the kitchen island. The granite is supported 7" by the island wall leaving 11" of overhang. The original installation used large wooden angle brackets that did not look good and were constantly in the way when sitting at the counter.This product worked perfectly. I cut the dry wall with an oscillating multi tool and recessed the hangers directly against the framing lumber. The directions in the box were informative, they recommend using an adhesive between the bracket and granite, it listed the size pilot hole to drill and recommended lubricating the screws ( I used soap).I am going to put ship lap horizontally under the over hang over drywall hiding the brackets. I will post a picture when the project is complete.I would definitely buy from FinkLLC again.

Recently had a bar countertop installed in the kitchen and needed support brackets for the quartz. These brackets were priced well amongst all the offerings and when they arrived, they did not disappoint. Heavy duty, feels nice to the touch, installation only took a few minutes. If I had one thing to change, I'd prefer the heads of the provided screws to have a better and more solid white paint job to them. Once installed in the white brackets and a white wall, the opaqueness of the screw head stands out. But this isn't enough to lose any stars.

These are heavy duty metal, the powder coat is great, the angle is spot on 90 degrees, has 3 holes on the bottom half to screw to the wall and seller includes screws.Some reviews stated that they had issues not being a perfect 90 degree angle, first thing I did was take out my digital angle tool and verify that they all are exactly 90, seller says they are done on a laser press or brake and it appears they are.I only needed 2 after seeing how sturdy they are, used three to make it look better.Been looking around for something to use the forth one on.

I had a piece of leftover butcher block from a bar project, so I used these brackets to make the side bar area for people overflow and food serving. the counter was about 12 inches so I was a little concerned about the sturdiness (only being 8 inches counter side, however these brackets being wide (almost 3 inches) the counter was solid on the wall. I did however drill holes in the counter portion of the brackets this way I can ensure the counter doesn't rock forward or move. The metal able to be drilled at ease for a screw hole. I wasn't aware, maybe I missed it, but the brackets also come with 4individual packs of 3 matching screws... and a bit! They are of good quality and didn't strip at all with the use of an impact driver.