Storage Studios Easy Access Paper Holder with 3-Slots, 9.5 x 13.5 x 14.5 Inches, Black (CH92579)

Great product and very durable

It helped me to use an old chapstick but you could wet a piece of soap and coat the edges of the pieces. It makes them glide together very easily. I didn't need a rubber hammer but it did take a little pushing to move the pieces along the respective tracks. I am not strong and I didn't think it was too difficult to move with the chapstick. I didn't use WD40 or vaseline because I didn't want remnants of it to get on my expensive papers. It would have been nice if the similar looking parts were labeled "bottom", "back", and the tracks labeled "front" and "back", but they're not, so here's an easy guide: Bottom and back look similar but the way to tell them apart and the order to assemble them is as follows:1.The bottom has the tracks on the smooth side which will face up and allow the insertion of the side pieces from front to back and it also has the stamped trademark on it which will face down towards your table and be positioned towards the back of the completed item. You will see that the tracks have an open end and a closed end, and the open ends are in front to allow the sides to slide in front to back.2. Look at the picture to see the shape and position of the sides as they slide in. I put one into the track the wrong way and it was slightly longer than the track. Had to back it out and flip it. If you feel a lot of resistance when sliding it into place, you're putting the wrong edge of the side into the track. Check the product picture and re-orient the side piece to ensure you're putting the correct edge into the track on the bottom. This is where I went wrong on one side piece and I could see how many reviewers think it was nearly impossible to slide those babies into the track.3. The remaining big piece is the back and the back ends of the side pieces slide into the four grooves ( or tracks) of the back piece from top to bottom. Note again the open and closed ends of the tracks. Slightly fiddly matching up the backs of the side pieces with the corresponding tracks on the back piece, but do-able.4. The last piece slides into the front edges of the side pieces.If you didn't get instructions, one of the reviewers here has kindly submitted a photo image of someone else's directions. I found it very helpful.

Anyone who's looked into storing their craft paper knows it's really hard to find affordable paper storage. This storage option is cheaply made and absolutely, 100% overpriced. I paid $30 for this and, while I don't recall selecting a warehouse deal, it came with a warehouse sticker. It's just thin plastic panels that make a box with dividers. It shouldn't cost $30-40 but it's better than nothing or paying many times more for fancy IKEA storage hacks or rolling drawer carts.Assembly does suck. One of the bigger pieces came cracked along one of the inner channels but I managed to assemble it without breaking it further. I considered using some sort of lubricant but didn't because I was scared of any residue getting on my paper. I found the easiest way to get the 2nd piece on was to brace the piece against me, grab the outside dividers and pull them towards me as far as they'll go (maybe an inch or so) and then pull the two middle ones to catch them up. It took forever, but it eventually worked.It holds a lot of paper and it's also big enough to hold my Cricut mats. There's probably 250-300 sheets of 8.5x11 paper in each section with room for 3 12x12 pads on one side and the cricut mats on the other.Improvements I'd like to see would be more substantial panels and maybe even solid dividers. When the holder is as full as it is, putting sheets in near the dividers creates potential for snagging and bending because the corners catch on the holes.All in all, I like it. I like it better than resorting to an accordian folder box for my letter sized sheets. I like it better than the $10 12x12 paper bag I purchased at the same time. I like it better than buying a cardboard classroom keeper or magazine holder. For the price, it's the best you can do.

Need to list "steak knife" as a required tool for assembly. This item comes in 7 pieces, with 3 solid panels and 4 dividers. The dividers are meant to slide into the runners on the panels, but it was a gigantic nightmare to get them to slide all at once. I was pushing with all of my force, and then the other side would pop out of the panel I'd already slid it into. I would get a panel halfway slid on, and then it would get totally stuck and I would have to strain to pry it off and start all over. I eventually had to take a steak knife and try to slice off part of the inside of the runners to make more space so it wasn't such a tight fit (pieces of plastic were in the way inside the runners), and even then, it was difficult to slide on. My palms have red lines on them from pushing so hard on the dividers and my palms still hurt. I eventually triumphed but I fear that every time I look at this stupid piece of plastic the memories will come flooding back and I'll get angry all over again.

Really hard to put together.

First, I totally love these paper holders! They are sturdy, look extremely nice on my storage unit and excellent storage and accessibility of my cardstock. I have several of them and highly recommend them. I must thank secret monkey's post in suggesting some chapstick on the slide-in rails! Just a very small amount will do. Put some on my finger and slid along the rails. This is the first time I assembled the unit in a couple of minutes. Just carefully look at and follow the included small instruction sheet. Assembly went so quick. I amazed myself! These, again, are excellent storage units and highly recommend them!

We use this to store rolled vinyl. Works well. Somewhat difficult to assemble.

Extremely hard to put together. Has taken about 2 hours to get pieces lined up.