Deep Pour Epoxy Resin Liquid Glass 3 GL Kit, 2-4 inch Super Clear Amazing Flow Casting Resin Kit, High Temp Heat UV Resistant Food Safe Epoxy, Bubble Free Low Viscosity Cast & Coat Stone Wood Metal

Do you know how to pour epoxy deep?. Then you will be entirely satisfied with this product. I built a live edge vanity top with tile inlay didn't even need the full capabilities of the epoxy. What a pleasure to work with. IF you are new to epoxy. This is a great starting point product. word of advice to all you who are epoxy pouring your ideas. FOLLOW THE DIRECTION with relaxed intensity; it is a must to be successful. Dust free and temperature controlled environment is also must for open surface pours. Its is also great for bowl mold forming for you turners out their looking to improve your game. you'll never need to pour beyond it maximum with a bowl form mold, and its great in incorporating pigment and mica powder. The products of your pours will be/are going to be stunning and out standing in appearance. YOU will be satisfied with this purchase. the clarity of glass when curing is compete. 72hrous is minimum time to perfection. DON'T rush. Mix twice and mix twice as long as the manufactures recommendations. two measuring cups/buckets for A & B separately, then 5 min each in two diff buckets when mixing, add pig and mica to first mixing bucket, pour to 2nd bucket and mix again, pour, and monitor for bubbles for at least the first 8 - 10 hrs on open surface pours or not using a pressure pot. Did I mention DO NOT RUSH!. Enjoy your pours and limitless possibilities. And about the BASE. make sure your forms will hold water. Pointless if epoxy can not be entirely contained within a form or mold - hint: 3M plastic masking film will sorta peal off once epoxy is cured but with difficult places in folds or creases. so you can line your forms with it to make waterproofing…. Smooth side of FRP board makes a great bottom to build your forms from.Addendum: The shipping is as quit as the system can move. I ordered at 5:30 their time so the business was closed. I checked next morning and product was already in shipping and on the way. The company cares about their products and provides the services and turn around you’d expect from a great company. Beyond all those great things to get you a great product total satisfaction is their goals.

Let me start off by saying this was to make an XMAS present for the wife. To say the least I didn't leave myself enough time and had to rush things. But I bought this product specifically due to its claim that it handles 2-4" pours. As you can see by the image, this was a tricky pour. I was trying to encapsulate a 3-dimensional object, that to say the least had mass and buoyancy which made it tricky. It wasn't wasn't something I could really do in multiple pours very well because of it's shape. Technically I think I probably could have done it in two pours, but I didn't have time.So I watched tons if videos, read the directions dozens of times, and tried to do my best. I've never done an epoxy mold, let alone one that had all the tricks this one had. it's not visible in the picture but there's actually a piece of all thread going through the bottom of the mold to secure the project to the walnut base. That alone was difficult.I started by creating a mold, I used melamine laminated particle board, partially because it's easy to cut, secure, and provides a pretty consistent surface when done properly. I had also hoped that because melamine is fairly non-porous, that it would help prevent the epoxy from sticking. I silicon caulked all seams and the all thread that was drilled through the side, into the base. The lit tree inside was zip tied to the all thread, and there was a piece of wood across the open top of the mold that I fed the wiring through, to hold it in place and securely. I also bought a pretty expensive epoxy release spray on Amazon that I covered the inside of the mold with, hoping it would help remove the wood when the product was cured.Most of this prep work was worth it, but I will say I don't think the release agent did any good. Based on the directions, I spent a lot of time creating the right environment for the cure. I hung plastic in my utility room and worked hard to effectively create a "paint booth" in an effort to be able to control the ambient temps. Where I am, the combustion air coming into my utility room was between 20F and 45F during the cure, so I put a space heater in the paint booth. There's no where else in the house I could have done this (especially since it was a gift and wife couldn't see it), and my garage often dips below freezing every night in the winter.On pour day, I heated the bottles using a heating pad and electric blanket, I mixed no more than 1G at a time, and followed the directions for length of mix, moving between buckets, etc. In general, the pour went pretty well. But almost immediately, some started leaking out of the hole for the all thread, even with caulk, so I'm guess it moved enough that it cracked the caulk. I scrambled to fix that with more caulk and even some good ol flex seal.This is where things went haywire for me. I paid so much attention to keeping the space between 72F and 75F, that I didn't pay attention to really the most critical thing, which wasn't really heating the product, but dissipating the heat from the reaction. I should have known, and I think the directions lacked some emphasis on heat during a deep pour. My pour was 3.5" deep. The heat it generated overnight was so much, that it cracked, created several crevices. So the next morning, when I found these, of course I kind of panicked, but I decided to work with it. I cleaned all of the surfaces as much as possible, did some light sanding, and used alcohol to clean it. I also vacuumed the cracks. I then mixed more epoxy, and started to fill the cracks and crevices. And boom, more issues. It turned out the expansion/contraction broke the caulk seals in the mold. So now it started leaking out a bunch. So I scrambled with more flex seal and caulk, trying to seal it up enough to contain the second pour.Surprisingly the second and third pours turned out fine. the product matched fine, of course you can still see them but they actually add a lot of character to the finished product. Structurally I think it's fine as well. I gave it 72hours before touching the mold, and then started to break it apart. This is where I don't think the mold release stuff did anything, the melamine was stuck to he epoxy like mad. I basically had to chisel, scrap, and sand the heck out of thing to get that off. Which basically meant I had to resurface the whole thing. That process was miserable, I used everything from a 40grit floor sander, to an orbital sander, to a dremel, and oscillating tool, with sand papers from 40 grit to 1000 grit. I used automotive rubbing compound and polish, as well as a buffing wheel. The surface still isn't very "polished" but it looks pretty good.In summary, my lessons learned were:- this can definitely be done by a novice. But it's not "easy"- for deep pours, heat control is in my opinion more important than keeping it warm- don't trust the "release agents"- when doing a mold that has an open top, remember to plan for that to be the finished side, it was much more polished and natural than the sides that were enclosed in the mold- Not really sure what else to have used for a mold, I though the melamine laminated wood was a great idea. I couldn't very well have used a silicon mold or something for a project this custom- polishing is hard work. I even tried to use diamond abrasives I use on tile and glass, didn't really work- the product worked well, it was only my misguided use that didn't make it perfect- finally, double and triple seal seams.

I did a lot of research before buying and this is what I loved. Has the UV protection, safe around food and just like it says poured crystal clear. Made in the US was important because of quality control and the manufacture answers question quickly. Doesn’t smell toxic. Super functional and easy to mix. Harden and adhered perfectly no bubbles at all. Dried faster than expected and was the perfect pour for the clear effect I wanted allowing the wood’s color to stay perfect. They shipped fast and all my orders have come early.

Solid product. Used a few different types of epoxy and this is my favorite. Easy to use, easy to mix and easy to mitigate the bubbles. Used it on a number of projects with good results on all. Keep the temperature controlled and don’t over heat and you will be fine!

So much better than the ultra clear I was using. Very few bubbles to pop. Much clearer in the end. Well worth the added cost. Takes longer to cure but the end result is amazing.

Quality product

Why did you pick this product vs others?:Not only is it a great product they have amazing customer service. Doubt I’ll ever buy resin from a different company. It’s great clarity. Just made a kitchen table with it and it came out amazing.

Good price and up to this point, the quality has been good. I don't really like the 2:1 ratio because I'm bad at math LOL, but mixes nice, sets up and is nice and clear.