LMS Data 6U 450mm Deep 19" Wall Mount Network Server Rack Data Cabinet, 19 inch Storage enclosure for Home Office Server Room with Glass Door, Removable Side Panels, Lockable Front-Rear - Flat-Packed

Good for the money. I ordered and then read the reviews, I didn’t hold out much hope but it’s pretty good. Fair enough it doesn’t have instructions and you have to build it yourself but as someone else said if you can build a home or office network then you can figure this out.Mine arrived and it was spotless, no marks on glass, no scratches to the body etc and plenty of screws.This is much cheaper than high end cabinets and it would show if they were side by side but this is perfect for the home or office, seems well designed and so on.I would by this again.

Purchased this 6U cabinet from Amazon, arrived promptly. Very good build quality and is ideal for my small LAN I run at home, used to house some Ethernet switches and some CCTV kit. Easy to put on a wall, just remember to use the appropriate wall fixings for the type of wall. Located my cab in my office and the removal sides allow me to do some post maintenance on the cabinet in situ. Fits the bill, will defy buy again.

Great little case, and not too bad to assemble. Issue I found is that it flexes too much! Just installing Unifi UDM SE caused the brackets to twist badly. Needs a support to keep the UDM straight.

First I need to point out that there are far more expensive cabinets on the market and the low cost of this particular cabinet needs to be considered when reviewing it!Also although I was using this in a home environment, hence not wanting to pay professional cabinet prices, I was installing equipment more commonly found in commercial I.T. installations including 2 managed POE switches which are reasonably heavy compared to simple unmanaged switches that would normally be used in a home or small business network.The pros:Cheap.Well packed and delivered quickly.Easy to assemble, especially if you have a power screwdriver.Comes with 10 rack cage nuts & screws - a nice bonus - most items of equipment need 4 screws each, but hey - 10 allows me to lose 2 and still mount 2 items.Panel edges are reasonably smooth - I spent quite some time leaning into this cabinet while it was on the wall to terminate cables and didn't get any cuts.The cons:A bit flimsy, I assume most of these will be wall mounted and the problem is that you are wary of applying too much torque to the screws in case you strip the holes but they need to be REALLY TIGHT in order for the panels not to move relative to each other and the cabinet not to sag when you load it with equipment. Othwrwise it goes out of square and the side doors cannot be easily removed or replaced due to the holes no longer being rectangular.The worst issue is the metal thickness of the rack mounting strips - if you install something such as a managed POE switch the rails really flex and the switch is nowhere near level. I doubt the strips will fail; the tilted switch just looks cosmetically poor. However 4 rails are supplied and since I was not mounting anything from the rear (the cabinet being wall-mounted) I used the spare rear strips to overlay the front ones to double-up on thickness, this solved the problem.Although the front door locks, the side panels do not - this is not unique to this cabinet and if I wanted a truly tamperproof cabinet I would need to pay a lot more money.Cable access: The partly pre-punched knock-outs in the top and bottom panels are quite a distance from the rear of the cabinet and if using wall mounted trunking for the cables the knock outs will not overlay the trunking; making neat cabling more difficult, it would have been better with the knockouts close to the rear.BUT! taking the price into account it still represents reasonable value.Steve.

Bought this rack to go in my loft. Assembly ok but as others have said instructions are useless. Once assembled it looks ok. Mounted in my UniFi network switch and the mounting rails are bending. They are made from barely 1mm metal and are just not up to the job. My switch is at a terrible angle and I have to make some kind of rear support. I am only mounting in 1 device so I can do something with it but tbh I should have just bought a better made rack. It’s going in loft otherwise I would have returned it. I might change the mounting rails for standard 2mm thick ones at a later stage. It’s all fixable but will end up costing more than if I just bought a decent one to start with

From the pictures this looked like a good cabinet. Unfortunately in reality the cabinet is made from very thin metal. The side panels, in particular, are so thin they don't fit well into the cabinet. The rails used to support your routers etc are just far too thin. I fitted a Ubiquiti rack-mounted router into the cabinet and it just sags about 1cm at the back because the rails just flex. So I ended up adding a block of wood at the back to support the router. The quality of the cabinet is just not good enough for its intended purpose particularly when you are paying £100 for what is essentially just a few sheets of pressed metal. A purchase I now really regret...

I bought this product, which, turned out to be the incorrect size for the devices I was installing, my fault, however, Veronica from IT Stockist kindly got back to me and even offered me a collection via DPD service. I said I will pack it and get back to her but I took so long to get back that I was actually outside of my return eligibility yet, upon asking if it was too late, without hesitation, Veronica replied to say it is Not a problem. Fortunately I scored a job and I didn’t have to return it in the end.The quality of the product itself is very good, once built, it is very solid and quite easy to assemble, I managed it without the instructions.Item came in a flat pack (I don’t know how the manufacturers managed to pack it so well).This is wall mountable and so simple to do so.All my future purchases for server racks will be from IT Stockist because simply because they sell good product and has one of the best customer service I’ve experienced!

This is a cracking little data cab. But just bare in mind it comes flat packed and allow 30 min to build.Top class for price.

Easy to assemble and install.

Montaje muy facil y calidad equivalente a los que valen el doble porque vienen montados. Lo volvería a comprar sin dudar. Por poco menos de 50€ dejas todos los aparatos de comunicaciones recogidos y no tienes los cables sueltos.