SPACECARE Retractable Workbench Casters Kit, Heavy Duty Workbenches Wheeels with 600 lbs Capacity, Adjustable Workbench Casters for Workbenches, Tables, and Cabinets, Easy to Install 4 Pack

Love love love these wheels.I installed them underneath a heavy wood shelves cabinet I built.They're easy to lower, move the cabinet around, then raise them up.A little pricey, but they're worth it. Would definitely buy again for another project.

I knew I needed something to be able to move my raise bed and these retractable wheels are it. I attached them to the outside leg using the enclosed template to screw then on installation was easy and they look great

Works amazing, very easy install. I would buy again. It would be a bit nicer to have a way to lock it into place. I sometimes find my self bumping into the latch and it popping up.

Floor-standing 6-inch jointers and 13-inch planers both need a base of nearly 2 ft x 2 ft. A handy lumber to use for a base is 5/4 (actual thickness = 1 inch) deck planking, which is heavy & strong yellow pine - and inexpensive. The 1-inch plank thickness works well with all the 1-inch #10 screws used. An 8 ft plank length is marginal, but they also come in 12 ft length (usually straight, but check). A 250 pound jointer can be outfitted with a base without ever having to lift it. Screw & glue a 3/4-inch thick x 1-inch or so wide runner along the inside bottom of two appropriate lengths (about 2 ft) of plank. Five 1.5-inch #6 or #8 screws should hold on their own if glue bond not strong. Tip the the jointer over until more than half of its housing length is resting on the two opposite runners. Use a rubber hammer to tap the two runners on their sides to keep containment, and tap them length-wise until they line up at each end ready to have the front & rear planks attached. Use 4 heavy gauge outside corner braces needing six 1-inch #10 wood or sheet metal screws each. If you mount the bottom of the caster wheel plate 1.75 above the frame bottom, the frame will clear the floor by 3/4-inch with wheels down, and rest solidly on its own legs with wheels up. (Keep focused on which way is up for the caster frames.). Be sure to leave a little room near the runner endpoints so that the jointer legs can reach through to the floor when wheels are up. The operation of lowering and raising the wheels is reasonably easy. The caster wheel assemblies come with everything needed, complete with lock washers and 24 1-inch #10 screws. Great product!A planer stand can be built with 2x3 legs, a 3/4-inch plywood top on a standard 1x4-inch board top frame, and the same 1-inch planking bottom frame. Screws of appropriate length can be used to secure the 2x3's to the upper and lower frames There are many mating surfaces in such a stand, and these can be glued & screwed to give strong stability with wheels up.

I put these on a pretty big work bench that I built. I had a cabinet on top of the work table, plus the bottom shelf full of supplies and a lathe, and they worked just fine. Definitely reccommend

Perfect on our wood table saw

Prior to purchasing these casters, I read a lot of reviews for this product. There seemed to be a common thread related to the failure of the mounting screws. This was useful information. My approach to mounting the casters was to drill a pilot hole using a 5/32 -inch drill bit, which is slightly oversized, to minimize drag on the screw. I also made sure to drill the pilot hole deeper than the screw length so that the entire travel length of the screw was within the pilot hole. I also used a standard Phillips screwdriver rather than a drill driver to insert the screws. I used 4 screws per mount, even though I have a relatively light workbench. The supplied template worked fine for locating the screws. I was able to mount the casters using the screws provided without any of the screws breaking. There was also a common concern regarding the stability of the casters. The primary complaint was that the casters would collapse while moving the workbench. I have not had that problem moving my bench across a concrete floor. However, I can see how that might be a problem moving over an uneven surface such as an asphalt driveway that's not as smooth as a concrete floor. The casters do not seem to be that firmly locked in the down position. Overall, I am satisfied with these casters. Installation was relatively easy, and so far, they've worked fine.

Box was damaged, instructions looked like they went thru the wash. Item looked OK though